Answered: .PL늘X 1 C10 11 in C10 PL블X11 11 in

Engineering

Civil Engineering

.PL늘X 1 C10 11 in C10 PL블X11 11 in

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

(See Attached picture of truss) 2. Since the reaction force at point A is 8975 #, The reaction force at point H is 7625#, the stress force in member AB is 14262 # (C), and the stress force in member BC is 11083# (T); calculate the minimum steel bolt size for attachment at points A and H. Use a factor of safety of 1.5 and a fitting factor of 1.15
A 16 mm-diameter steel rod AB is fitted to a round hole near end Cof the wooden member CD. For the loading shown, determine, (a) the distance b for which the average shearing stress is 7MPA on the surfaces indicated by the dashed lines, (provide FBD and answer in mm)(b) the average bearing stress on the wood (provide FBD and answer in MPa) 25 mm. 8000N 4000N A 100 mm D 4000N C
Q2: Select a tension member is to consist of two C10 channels and two PL 1/2 x 11, arranged as shown in Figure below to support the service loads, PD= 200 k and PL= 320 k. The member is assumed to be 30 ft long and is to have four lines of 3/4-in Ø bolts. 30 degrees Assume U= 0.85. All steel will be A36. PL늘X1 C10 C10 11 in PL x 11 11 in
Problem For the frame shown, design the maximum permissible value of P with a factor of safety of 2.5. Design the maximum permissible value of P based on the following conditions: ✓ Ultimate tensile strength of each member CD is 300 ksi Ultimate shear strength of the bolts in A, C, E, and F is 200 ksi ✓ Ultimate bearing strength of member BDE is 150 ksi ✓ Ultimate bearing strength of the support plates is 250 ksi Members CD and BDE have cross-sectional dimensions of 5 in x 3 in (the larger dimension is the width). The diameters of the bolts are as follows: A and B - 1.5 in: C and D-2 in E and F - 1 in. 1.5 in. thick Support Plates -2 ft + D 3 ft B 2 in thick Support Mate Solution Step 1. Identify the conditions for design. Stress normal stress in each member CD, OCD shear stress in bolt A, TA shear stress in bolt C, T shear stress in bolt E, T shear stress in bolt F, T bearing stress on member BDE due to: bolt B, BDE-B bolt D, OBDE-D bolt E, OBDE-E bearing stress on support plates at…
J 6 The cast iron bearing seat in the picture is bolted to the steel beam of the ceiling bracket and supports the gravity load. Use M20 coarse thread ISO class 8.8 bolts with a thickness of 3.4 mm The steel washers are placed under the bolt head and nut. The flange of this bracket is 20 mm thick, the shaft The elastic modulus of the bearing is 135 GPa. (a) Assuming this is a permanent joint and the fasteners are lubricated when assembled, find the required wrench torque. (b) If the gravity load is 15 kN, try to find the load factor n of the design.
The five-bolt connection shown must support an applied load of P = 300 N. The thickness of the axial member: = 1.5 mm. and the width = 18 mm If the ultimate shear stress in the bolts must be limited to 265 MPa with F.O.S = 3.7 . And the ultimate normal stress in the axial member = 250 MPa, with F.O.S = 2.8 , And the ultimate bearing stress in the axial member = 110 MPa, F.O.S = 2.5 Determine the minimum bolt diameter that may be used in the connection
A double-angle shape, 2L7 3 4 3 3⁄8, is used as a tension member. The twoangles are connected to a gusset plate with 7⁄8-inch-diameter bolts throughthe 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used.a. Compute the design strength.b. Compute the allowable strength.
a) Compute the allowable block shear strength of the plates in KN. b) Check the adequacy of the plates. c) If W14 x 193 is used, compute the allowable strength (KN) based on fracture of the net section. d) Select the lightest W shape for the tension member. e) What is the allowable block shear strength in KN of the lightest W shape?
a welded connection is in eqilibrium under the action of the four forces shown. Knowing that FA=8lbs and FB= 16lbs, determine the magnitudes of other two forces *3dec places all final
SOLVE FOR1 HR
Design the reinforcements of the given T beam below. bf=900mm bw=420mm tf-120mm d=550mm d'=80mm fc'=34MPa fy=415MPa USE NSCP 2015 A.Mu = 1300kN-m, As = mm2 B.Mu = 1800kN-m, As = mm2, As' = mm2
SITUATION B. strength and the allowable strength considering the following members. Analyze the members separately except for No.7. 5. 6. Given the connection below bolted with M22 bolts, solve for the design tensile A992 W360x122 A36 L152X102X14.3 7. Built-up Section with Ey=345 MPa and Fu=450 MPa W 360 X 122 75 100 mm 100 -P L152X102X14.3 bf/2