Plot the V curves (no load, partial loads and full load) for a 7.2 kW, 208 V, three phase, star connected synchronous motor by varying the power factor from 0.5 lagging to 0.5 leading. The synchronous reactance of the motor is 4Ω/phase and the winding resistance is negligible. Assume Ea= 100 Ifwhere Ifis the field winding current

Plot the V curves (no load, partial loads and full load) for a 7.2 kW, 208 V, three phase, star connected synchronous motor by varying the power factor from 0.5 lagging to 0.5 leading. The synchronous reactance of the motor is 4Ω/phase and the winding resistance is negligible. Assume Ea= 100 Ifwhere Ifis the field winding current

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter39: Synchronous Motor Operation

Section: Chapter Questions

Problem 14SQ: Induction motors and welding transformers require magnetizing current, which causes a. lagging power...

See similar textbooks

Similar questions

T-a. The direction of rotation of a single-phase split-phase motor can be change by........ a) reversing the connection of the start winding b) reversing the connection of the run winding c) reversing the connection of the start and run winding at the same time d) "a" or "b", not "c" T-b. Single-phase split-phase motors using an electrolytic capacitor in the start winding circuit should not be cycled more than about__________ time per hour. a) 8 b) 12 c) 24 d) none of the above T-c. When replacing the capacitor in a capacitor-start induction-run motor, one must be sure to replace the bad capacitor with__________ . a) a smaller one b) one of the same size c) a larger one d) none of the above
3-Phase 50Hz 6 pole induction motor has rotor resistance of 0.1 ohm and reactance of 0.92. ignore voltage drop in stator and assume thee rotor resistance is constant. Full load slip is 3%, then find Tmax /Tfl
A 3-0, 50-Hz induction motor with its rotor star-connected gives 500 V (r.m.s.) at standstill between slip-rings on open circuit. Calculate the current and power factor in each phase of the rotor windings at standstill when joined to a star-connected circuit, each limb of which has a resistance of 10 Q and an inductance of 0.03 H. The resistance per phase of the rotor windings is 0.2 Q and inductance 0.03 H. Calculate also the current and power factor in each rotor phase when the rings are short- circuited and the motor is running with a slip of 4 per cent. [13.6 A, 0.48; 27.0 A, 0.47] (London University) A 4-pole, 50-Hz, 3-phase induction motor has a slip-ring rotor with a resistance and standstill reactance of 0.04 2 and 0.2 2 per phase respectively. Find the amount of resistance to be inserted in each rotor phase to obtain full-load torque at starting. What will be the approximate power factor in the rotor at this instant ? The slip at full-load is 3 per cent. [0.084 2, 0.516 p.f.]…
Armature reaction in an alternator primarily affects: A: rotor speed B: terminal voltage per phase C: frequency of armature current D: generated voltage per phase
A 6-pole, 3-phase induction motor is connected to a 25 Hz supply and at full load the rotor e.m.f. makes 105 complete cycles in 2 minutes. The full load percentage slip is
A value of magnetizing current in a 3-phase induction motor * gives power factor smaller .. larger smaller. .poor large . better O large...poor O
Here it is the equivalent circuit of and induction motor and it is per phase circuit my question is name for me the variable for example R1 is the winding resistance and so an the all variable and please show me a pic of the real machine with the variable for example for R1 happens because of the winding i need to see the winding in the real machine, please help me to understand well
3.An induction motor has a rotor resistance and reactance at standstill of 0.1 ohm and 3.5 ohm respectively. At standstill the voltage induced to the rotor is 60volts per phase. If the slip is 5%, determine the rotor current
Induction motors and welding transformers require magnetizing current, which causes a. lagging power factor. b. leading power factor. c. unity power factor. d. zero power factor.
A three-phase, 3.3 kV, 50 Hz power supply is used to drive an induction motor. The motor has an eight-pole, star-connected stator. The rotor is also star-connected, with the line ends brought out to sliprings for starting and speed control. At standstill, the open circuit voltage induced on the rotor, as measured between the sliprings, is 1475 V. At the full load speed, the frequency of the induced emf on the rotor winding is 2.5 Hz. The motor has the following parameters: Rc = 250 Q R₁ = 0.1Q Xm=250 X₁ = 0.35 Q R2 = 0.04X2 = 0.30 By referring the rotor quantities to the stator, calculate the following: (i) The shaft output power and torque of the fully loaded motor, if the corresponding friction and windage losses are 44 kW;
A 6-pole, 3-phase, 50Hz induction motor is running at full-load with a slip of 4%. Therotor is star-connected and its resistance and standstill reactance are 0.25Ω and 1.5Ω perphase. The e.m.f. between slip rings is 31 V. Find the rotor current per phase and p.f.assuming the slip rings are short-circuited.