pllllzzzz help me right nowww plzzz  The belt moves at a steady velocity V and skims the top of oil tank. Assuming a linear velocity profile in the oil, what is the required belt-drive power P (watt) (P= power = force x Velocity) if the belt moves at 3.5 m/s over oil with specific gravity of S=3.6 and oil viscosity of 0.004 m2/s. Belt geometry L= 2 m, b = 60 cm, and oil depth is h = 3 cm?

Q: The flow regime pattern for an oil reservoir as the fluid moves from bottomhole to the surface is…

A: The following is the most likely flow regime pattern for an oil reservoir as the fluid moves from…

Q: The space between two square flat parallel plates is filled with oil. Each side of the plate is 540…

A:

Q: Q1 A smooth cylinder of 50.1 mm inside diameter and 150 m long is placed with its axis vertical. If…

A:

Q: Calculate the pressure difference between the two points РА- Рв A B oil S.G 0.91 y 10cm Hg

A: To determine the difference of pressures at points A and B

Q: A 10kg box slides on a ramp with a slope of 30°. There is a thin layer of oil with a N.s viscosity…

A:

Q: 1. For the shown conic body which rotating with constant angular ity 10 rad/s, find the torque which…

A:

Q: In between plates the oil thickness is 33 mm maintained and the top plate moves at 62 cm/s. Find the…

A: Ans is 18.78/s

Q: A 3d block with the dimensions of 50cm by 30cm by 20cm and a weight of 450 N, is going to be moved…

A:

Q: The apparatus shown in the figure is to coat a thin steel plate with oil. using for. Fluid1 has a…

A:

Q: A plate of area 2.15 m is pulled with a speed of 0.3 m/s relative to another plate located at 3.5 mm…

A:

Q: Valve works in oil which creates a viscous resistance proporti velocity at the rate of 10 N/(m/s).…

A:

Q: mie Departments ETC - CIMS - (a). A lubricating oil having the dynamic viscosity of 0.057 poise and…

A: . ,

Q: 3. A capilary tube of inside diameter 6 mm connects tank A and open container B, as shown in figure.…

A:

Q: Q3/ write an equation for cases below for surface tension 1- Spherical bubble. 2- cylinder supported…

A:

Q: What is meant by hydrostatics? Write the fundamental equation for pressure variation with depth in a…

A: Hydrostatic: It is a branch of science which deals with the characteristics of the fluid when it is…

Q: The belt moves at a steady velocity V and skims the op of oil tank. Assuming a linear velocity…

A:

Q: Figure 1 shows a box of mass m that is supported on a surface inclined at angle 0 to the horizontal.…

A:

Q: Q2) 25-mm diameter shaft is pulled through a cylindrical bearing as shown in Fig.2. The lubricant…

A:

Q: Given the following illustration, the pressure at A (far left) is PA = 81.4 psi, the pressure at B…

A: Dear student, for the sake of simplicity I have converted all the data in SI unit but final answer I…

Q: Q 15: The property of a fluid which determines its resistance to shearing stress :is called…

A: Solution is given below:

Q: s stoves, the recommended lubricant to be used in gas flow control valves is: No lubrication needed…

A: For gas stove, the lubricant is used in gas control valve as  Molybdenum disulfide or graphite…

Q: 3. A closed tank is at 20. If the pressure at point A is 98 kPa. What is the absolute pressure at…

A: Given Data The temperature of the closed tank is: T=20°C The pressure at the point A is: PA=98 kPa…

Q: A hydrodynamic journal bearing is subject to 2000 N load at a rotational speed of 2000 rpm Both…

A:

Q: Estimate the density of a 0.8-specific gravity dead oil at 40 C

A: Given data Specific Gravity of oil = 0.8  Temperature at which it is measured = 40°C

Q: H.w 1: gas in vessel has pressure (140 kpa) and volume (0.1m) and Temperature (22 C) .The gas is…

A: Initial condition - P1 = 140 kPa, T1 = 22 oC = 295 K, V1 = 0.1 m3 After compression, Final condition…

Q: Two plates are separated by 30 mm space. The lower plate moves at velocity of 2 m/s while the upper…

A:

Q: shear stress in Pascals on the surface of top plate

A: Given data; v=7.4×10-7 m2/sS=0.88ρ=1000×0.88=880KG/m3U=0.5M/Sh=0.5mm=0.0005m

Q: SAE 10W-30 oil with viscosity 1 x 10-4 lbf s/ft2 is used as a lubricant between two parts of a…

A:

Q: Question 1. The apparatus shown in the figure is used to coat a thin steel plate with oil. Fluid1 is…

A:

Q: ?What is the total force lifting the tank

A:

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and kinematic viscosity of…

A:

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.052 poise and kinematic viscosity of…

A: As per bartleby guidelines we are allowed to solve only 1st 3 subpart of a question.  Please post…

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.