Handwritten plzzzz asap...i'll give you more vote... A valve of piston type has a mass of 7 kg and is driven withS.H.M. that can be referred to a vector of length 60 mm rotating at 24 rad/s.The valve works in oil which creates a viscous resistance proportional to thevelocity at the rate of 10 N/(m/s). Events controlled by the valve occur when itis 30 mm from its mid-position and moving towards it and, again, when it is20 mm beyond its mid-position on the same stroke. Determine the timebetween these events. Evaluate the viscous resisting force at the first event andthe force in the driving rod at the second.

Answered: Image /qna-images/answer/32cc241f-ab76-49a3-9d38-0a351c90166a.jpg

Valve works in oil which creates a viscous resistance proporti velocity at the rate of 10 N/(m/s). Events controlled by the valve oca is 30 mm from its mid-position and moving towards it and, again, 20 mm beyond its mid-position on the same stroke. Determine between these events. Evaluate the viscous resisting force at the first the force in the driving rod at the second.

Valve works in oil which creates a viscous resistance proporti velocity at the rate of 10 N/(m/s). Events controlled by the valve oca is 30 mm from its mid-position and moving towards it and, again, 20 mm beyond its mid-position on the same stroke. Determine between these events. Evaluate the viscous resisting force at the first the force in the driving rod at the second.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cylindrical casting of diameter 200 mm and height 100 mm is to be casted. From the previous observations it was found that to cast a shaft of 150 mm diameter and 500 mm length, the casting time is 30 min. Determine the casting time of the cylindrical casting. Take constant n= 2. %3D Answer Choices: a. 165 minutes b. 5.44 minutes c. 54.4 minutes d. 65 minutes
20.1
Dont keep asking for a clear pic. This is what i have. And the data is conplete. Solve it using given data itself.
Beam loaded as shown in Fig. below. Determine the Following: Reaction support at point B. a. 56KN (Downward Direction) b. 56KN (Upward Direction) c. 35KN (Downward Direction) d. 35KN (Upward Direction) Reaction support at point D. a. 26 KN (Downward Direction) b. 26 KN (Upward Direction) c. 24KN (Downward Direction) d. 24KN (Upward Direction) Shear force equation of section AB. a. -30KN b. 30KN c. -32KN d. 32KN Shear force equation of section CD. a. -24KN b. 24KN c. -28KN d. 28KN Bending moment equation of section BC. a. 26KN(x)+56KN.m b. 26KN(x)-56KN.m c. -26KN(x)+56KN.m d. None of the above. Maximum bending moment of the beam. a. 47KN.m b. 46KN.m c. 48KN.m d. None of the above
Q1. What is sheet metal working? Write any four products made through the sheet metal processing. Explain in detail about the galvanized iron and stainless steel sheet metal materials.
I need answer within 20 minutes please please with my best wishes
Question # 4 A cup of height h=30 mm and diameter d = 50 mm is to be drawn from a steel sheet of 2 mm thickness. a) Calculate the blank diameter Db. b) The Drawing ratio (DR). c) The shearing force needed to cut this blank if the shear strength of the steel sheet is S=180 N/mm2
23- Complete the sentence with the appropriate terminology. In .. a simple punch and die that each have the included angle are used to bend the part. wrinkling b) tearing edge bending V-bending e) earing
You have the following information: (IMAGE) Taking into account the above, answer the following questions: 1) Calculate the safety stock that allows for 5 stockouts in a year. 2) Calculate the reorder point that will allow for these 5 stockouts in a year. 3) Calculate the number of stockouts in a year, corresponding to a safety factor of 0.84. 4) Calculate the reorder point that allows the number of stockouts corresponding to a safety factor of 0.84.
Q2) Choose the correct answer for only 15 (fifteen) of the following. is about 67% of the total forces. A) Longitudinal force. 1) In turning operation, the force. E) thrust force. B) Radial C) feed force. D) cutting force. (C) 2) Which one of the following materials has the lowest hardness: (a) aluminum oxide, (b) cubic boron nitride, f) none of the previous answers. high-speed steel, (d) titanium carbide, or (e) tungsten carbide Which one of the following operations is generally capable of the closest tolerances: (a) broaching. (b) drilling, (c) end milling, (d) planning, or (e) shaping. F) none of the previous answers. 3)
16)
.....*. .................... Answer with True or False: Writing a proposal takes extensive research, reflection, drafting, organizing, and revision Select one: True False