Question 1. The apparatus shown in the figure is used to coat a thin steel plate with oil. Fluid1 is oil with a viscosity of 0.02 Pa.s, Fluid2 is 0.001 Pa.s. If h = 4 mm and the total oil-steel contact area is 20 m², calculate the force required to move the steel at 5 m/s. Suppose the velocity profile in the fluid is linear.

Q: For the conic body shown in Figure (3) which rotating with constant angular velocity of 12 rad/s,…

A:

Q: An inclined pipe of 4-inch ID is used to transport a viscous oil from one open-top container A to…

A:

Q: The space between two square flat parallel plates is filled with oil. Each side of the plate is 540…

A:

Q: HYDRAULICS Support your answer with the appropriate solution and diagram. 1. An oil of viscosity 5…

A:

Q: A 10kg box slides on a ramp with a slope of 30°. There is a thin layer of oil with a N.s viscosity…

A:

Q: In between plates the oil thickness is 33 mm maintained and the top plate moves at 62 cm/s. Find the…

A: Ans is 18.78/s

Q: A 3d block with the dimensions of 50cm by 30cm by 20cm and a weight of 450 N, is going to be moved…

A:

Q: The apparatus shown in the figure is to coat a thin steel plate with oil. using for. Fluid1 has a…

A:

Q: A plate of area 2.15 m is pulled with a speed of 0.3 m/s relative to another plate located at 3.5 mm…

A:

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

A: Given data diameter of shaft (d) = 250 mm  diameter of sleeve (D) = 251 mm Power required = 2204 W N…

Q: Figure 1 shows a box of mass m that is supported on a surface inclined at angle 0 to the horizontal.…

A:

Q: Given the following illustration, the pressure at A (far left) is PA = 81.4 psi, the pressure at B…

A: Dear student, for the sake of simplicity I have converted all the data in SI unit but final answer I…

Q: · Complete the following. As shown in Figure (1) oil of viscosity (0.006 Kg/m.s) fills the small gap…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Figure 1 shows a layer of oil(8.95 kN/m^3),

A:

Q: Two parallel flat plates are spaced 2 in. apart. One plate is moving at a velocity of 10 ft/min and…

A:

Q: An iron block with dimensions of 0.25x0.25x0.25 m; It slides over an inclined plane with an…

A: V=0.25m×0.25m×0.25mθ=30ot=0.0069mm=6.96×10-6 mμ=7.5mPa s=7.5×10-3  Pa-sρ=7800 kg/m3

Q: C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and kinematic viscosity of…

A: C1 (a): Given data: Dynamic viscosity of lubricating oil, μ=0.058 poise and it's kinematic viscosity…

Q: A tube length of 40 cm and a radius of 5 cm passes through the liquid. the viscosity coefficient is…

A:

Q: Working for an engineering consultancy firm, your knowledge of fluid dynamics is required to design…

A: Disclaimer from Bartleby:Hello. Since your question has multiple sub-parts, we will solve the first…

Q: pllllzzzz help me right nowww plzzz  The belt moves at a steady velocity V and skims the top of oil…

A: Given data: V= 3.5 m/s L= 2 m b = 60 cm h = 3 cm Need to determine the required belt-drive power.

Q: Q2) ) If the vertical component of the hydrostatic force on the gate BC shown in fig.2 is 1200 kN…

A: Assume that width of the gate is w and vertical component of force act on face BC is 1200kN . So…

Q: A plunger (54 mm Ø and 0.5 m long) is moving through a horizontal cylinder (60 mm Ø) containing oil…

A: Given   Specific gravity, SG = 0.84  Kinematic viscosity = 7.1x10-6 m2/sec              Diameter, D…

Q: water is heated from 25 C to 65 C as it flows through a 100-mm ID tube.Calculate viscosity of the…

A:

Q: PROBLEM 2.0 Determine the viscosity of a fluid having kinematic viscosity 6 stokes and specific…

A: Given data: kinematic viscosityv=6 stokesSG=1.9 Need to determine the viscosity of the fluid.

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

A: Given data: The height of the lubricant is

Q: lunger having diameter of 10 inch slides in a 10.006 inch diameter of a cylinder, the annular space…

A: In the question we have,kinematic viscosityϑ=0.004 ft2/sDiameter of plungerdp=10 inchDiameter of…

Q: A viscosity motor/pump is shown in figure below. The rotor is concentric within a stationary…

A: The value are .The flow rate is .The dynamic viscosity is .

Q: ?What is the shear force that acts on the circumference of the piston (N) Assume the variation in…

A:

Q: Figure 1 shows a layer of oil (8.95 kN/m), the thickness of 0.3 mm, between two parallel flat…

A: Given,  Weight density of the oil , ρg =8.95 KN/m3 Thickness of the oil layer , h = 0.3 mm Velocity…

Q: A flat area 1.5x106mm² is pulled with a speed of 0.4m/s relative to another plate located at a…

A: Given data: A=1.5×106 mm2=159×10-6 m2du=0.4 m/sdy=0.15 mmμ=1 poise=0.1 Pa.s Need to determine the…

Q: PROBLEM 1.0 A flat area 1.5x10mm² is pulled with a speed of 0.4m/s relative to another plate located…

A:

Q: fluid having a density of 1400 kg/m³ stands in a tube of 6 mmθ at a height of 27 mm. what is the…

A:

Q: Q1:- A 300 mm diameter of pipes and 350 mm long slides along a large diameter cylinder at a speed of…

A:

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.