Please mark out the helical direction of the helical gear. The axial forces on the shaft shouldbe opposite if there two gear/worm on one shaft.

Answered: Image /qna-images/answer/b38d2ce2-d9a9-4148-898b-6d2c6bb8ea1a.jpg

Answered: Please mark out the helical direction…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The teeth of the gear arrangement have Gear A=40teeth, Gear B=70 teeth and Gear C= 50teeth, a pinion (driver Gear) that rotates at 625 rpm, and idler Gear B and a driven gear (Gear C). The gears have a module of 5mm and a pressure angle of 200. Find the pitch diameter of gear C in mm.
1. Two metric spur gears are engaged; the gear ratio is 3/2 and they have a module of 2.5 mm. Find the number of teeth for each gear if the center distance is 125 mm.
Two internal 10-pitch, 20° full-depth gears are used in a system. The pinion has 28 teeth and the gear has 70 teeth. Determine the center distance.
The gearing of a machine tool is shown. The motor shaft A is connected to gear 1 and rotates at 1000 rpm. Gears 2, 3, 4, and 5 are fixed to parallel shafts rotating together. Thefinal gear 6 is fixed on the output shaft. Determine the following considering the number of teeth on each gear below:a. Speed of gear 2, 3, 4, 5, and 6b. Speed ratio of the gear trainc. Train value of the gear trainGEAR 1 2 3 4 5 6NO. OF TEETH 24 53 27 68 28 64
Confused with answers (2/3 or 3/2) Please show clear work
A 12-tooth external spur gear A, rotating clockwise, drives a gear B whose diametral pitch is 4. The ratio of the speed of gear A to gear B is 2 to 1. The tooth proportions are standard 14-¹2° brown and sharpe. (1) Placing the center of gear A on a vertical line above the center of B on the same vertical line show and give the diameters of the pitch circles, addendum circles, and dedendum circles. (2) Sketch in roughly enough of a tooth on each gear in contact at the pitch point and indicate the face of the tooth, the flank of the tooth and the pitch point. (Please do indicate the computations, most especially the drawings. Thank you!)
A compound epicyclic gear train. Wheels A, D, and E are free to rotate independently on spindle O, while B and C are compound and rotate together on spindle P, on the end of arm OP. All the teeth on different gears have the same module. A, B, and C have 14 teeth, 32 teeth, and 16 teeth respectively, which are cut externally. a) Find the number of teeth on wheels D and E which are cut internally. b) Determine the magnitude and direction of the angular velocities of arm OP and gear E If wheel A is driven counterclockwise at 2 r.p.m while D is driven clockwise at 6 r.p.m., and the number of teeth of gears E and D, are 78 and 62 respectively. (Must use Tabular method) another method not accepted). Steps nber of teeth Step1 Step2 Arm OP Gear A Gear B Gear C Gear D Gear E A
1. The speed ratio of the reverted gear train, as shown in Fig, is to be 12. The module pitch of gears A and B is 3.125 mm and of gears C and D is 2.5 mm. Calculate the suitable numbers of teeth for the gears. No gear is to have less than 24 teeth. Driver 200 mm Driver Driven 2. In a reverted gear train, as shown in Fig., two shafts A and B are in the same straight line and are geared together through an intermediate parallel shaft C. The gears connecting the shafts A and C have a module of 2 mm and those connecting the shafts C and B have a module of 4.5 mm. The speed of shaft A is to be about but greater than 12 times the speed of shaft B, and the ratio at each reduction is same. Find suitable number of teeth for gears. The number of teeth of each gear is to be a minimum but not less than 16. Also find the exact velocity ratio and the distance of shaft C from A and B 200 mm Driven
Do it your own
Please don't give stupid answer read the question carefully. Clarify whether the answer is 2/3 or 3/2.
The gear ratio shown must transmit 10 horsepower (66000 lb in/s) from its input, which is rotating at a speed of 1200 revolutions per minute. It must increase the torque received at its input shaft 16 times. Spur gears with 20° pressure angle should be used. Input and output shafts should be aligned. The transmission should take up as little space as possible. The distance between the centers of the input shaft and the intermediate shaft (the one that loads gears 3 and 4) should be 10 inches. Determine the magnitude of the radial load that gear 4 exerts on gear 4. Write your answer in pounds.
i need the answer quickly

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

Please mark out the helical direction of the helical gear. The axial forces on the shaft should be opposite if there two gear/worm on one shaft.