A compound epicyclic gear train. Wheels A, D, and E are free to rotate independently on spindle O, while B and C are compound and rotate together on spindle P, on the end of arm OP. All the teeth on different gears have the same module. A, B, and C have 14 teeth, 32 teeth, and 16 teeth respectively, which are cut externally. a) Find the number of teeth on wheels D and E which are cut internally. b) Determine the magnitude and direction of the angular velocities of arm OP and gear E If wheel A is driven counterclockwise at 2 r.p.m while D is driven clockwise at 6 r.p.m., and the number of teeth of gears E and D, are 78 and 62 respectively. (Must use Tabular method) another method not accepted). Steps nber of teeth Step1 Step2 Arm OP Gear A Gear B Gear C Gear D Gear E DA

A compound epicyclic gear train. Wheels A, D, and E are free to rotate independently on spindle O, while B and C are compound and rotate together on spindle P, on the end of arm OP. All the teeth on different gears have the same module. A, B, and C have 14 teeth, 32 teeth, and 16 teeth respectively, which are cut externally. a) Find the number of teeth on wheels D and E which are cut internally. b) Determine the magnitude and direction of the angular velocities of arm OP and gear E If wheel A is driven counterclockwise at 2 r.p.m while D is driven clockwise at 6 r.p.m., and the number of teeth of gears E and D, are 78 and 62 respectively. (Must use Tabular method) another method not accepted). Steps nber of teeth Step1 Step2 Arm OP Gear A Gear B Gear C Gear D Gear E DA

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: n a compound train of gears spur gear 1, with 40 teeth and rotating at 15 rpm, drives a pinion 6…

Q: State an equation tha relate the number of teeth of gear D, B and C.

Q: (B) The sun and plant gear of an epicyclical shown in figure below the annular gear D has 100…

Q: The lath machine in the university mechanical workshop uses epicyclic gear train shown in Figure 1…

Q: The center distance between the two gear is 250mm and module is 5cm. Find the number of the teeth of…

A: module=diameter/teeth

Q: A 14.5° involute spur gear has a pitch diameter of 3 in. Determine the diameter of the base circle…

A: Given information, Pitch circle radius= 3/2 =1.5 inch, Find, Base circle diameter

Q: A 84-tooth gear is driven by a 17-tooth spur pinion. The diametral pitch is 32 teeth/in and the…

A: Given: Number of teeth on the pinion (Tp)=17 Number of teeth on the gear (TG)=84 Diametral Pitch…

Q: A 20 straight-tooth bevel pinion having 14 teeth and a diametral pitch of 4 teeth/in drives a…

A: Given Data: Number of teeth in Bevel pinion NP=14 Diametral pitch P=4 teeth/in Number of teeth in…

Q: nning at 100 rpm clockwise. B is an output shaft running at 250 rpm clockwise. Torque on A i

A: given:NA=100RPMNB=250RPMTA=50KN-m

Q: The lath machine in the ( mechanical workshop uses epicyclic gear train snuwn in Figure 1 to…

A: given data; ⇒pitch circle dialmeter (d) of gear D=214mm⇒module (m)=4mm⇒speed of arm(y)=1…

Q: A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has 4 wheels of the…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: a left-hand helix angle of 35°, a normal pressure angle of 26°, and a normal module of 3 mm. Find:…

A: (a) Write the given data. No. of tooth on pinion, Z1=15No. of tooth on gear, Z2=37α=35°ϕn=26°mn=3 mm

Q: The lath machine in the Central University of Technology (CUT) mechanical workshop uses epicyclic…

A: Given: The pitch circle diameter of gear D, dz = 214 mm The module of ring gear, m = 4 mm The number…

Q: A power of 25 KW is transmitted by a pair of spur gears. Pressure angle= 20, radial force generated…

A: Given, P = 25 kW, θ = 20 0, Fr = 220 daN = 2200 N, N = 600 N, t = 33, Dp2 / Dp1 = 3 We need to find…

Q: For the gear train shown in the figure. Planet gears 3, 4, and 5 are rigidly connected to a common…

A: The speed of gear 1 is 30 rpmN1=10N3=24N4=N5=12N6=10N7=30we need to determine speed of the gear 7…

Q: 160 rpm ccw about the center of gear 1, which is fixed. 1) Predict the speed of the gear 2. 2)…

Q: Q6 (a) The set of double reduction gears shown in Figure Q6 (a) is driven by a pinion (Gear A) with…

Q: A two-stage gear train consists of four gears meshed together (Figure 10). The secondand third gears…

A: for the given gear train To determine angular velocity of gear 4 in terms of ω1,n1,n2,n3 and n4

Q: The lathe machine in the Central University of Technology mechanical workshop uses epicyclic gear…

Q: rpm of D in the clockwise direction is

A: Figure shows the epicyclic gear train.For this data is given as: Number of teeth on the gears;…

Q: A gear system consisting of a pinion and an internally toothed wheel is shown in Figure 3.1. The…

A: Given: The number of tooth on pinion, Zp = 21 The module, m = 5 mm The pressure angle, α = 20° The…

Q: nism when annulus is i

A: introduction: we have to find out degree of freedom

Q: A helical gearset has 1.5 mm module and a pressure angle of 20°. The width of gears is 40 mm, the…

A: Given Data: The module of the gearset, m=1.5 mm Pressure angle, 20 Width of the gears, b=40 mm…

Q: If there are three gears A, B, C number of teeth in A is 32, B is 45, and C is 48. B is the idler…

Q: Q(1): For the component epicyclic gear train shown in the figure, the number of teeth of gears (A, B…

A: Given diagram:

Q: Two internal 10-pitch, 20° full-depth gears are used in a system. The pinion has 28 teeth and the…

A: Given Data The number of teeth on pinion is:t1=28 The number of teeth on the gear is:t2=70 The…

Q: An epicyclic gear shown in Figure 1 consists of ring gear, planet gear and sun gear. The ring gear…

A: Given Data Ts=32 teeth Tr=72 teeth Arm y=20 rpm

Q: For the gear train shown in the figure. Planet gears 3, 4, and 5 are rigidly connected to a common…

A: The speed of gear 1 is 30 rpmN1=10N3=24N4=N5=12N6=20N7=30determine the speed of gear 7 and the speed…

Q: has gears A and an annular gears D & E free

Q: lb pair of bevel gears having 20 and 75 teeth are used on axes that intersect at a 90" angle.…

Q: i. A parallel helical gearset uses a 20-tooth pinion driving a 46-tooth gear. The pinion has a…

A: Since we only answer upto three subparts we will answer the first three. Please resubmit the…

Q: what is the force value at the bar?

A: Given Gear Ratio, G = 30/1 Power of electric motor, P = 1hp To find - Value of force at bar

Concept explainers

Power Transmission Elements

It is defined as the energy transfer from one location to another location. The energy will start moving from the energy generation source to the energy applied position to obtain the work output. From this method, a large amount of electric energy moves from the power station to various electrical substations.

Question

A compound epicyclic gear train. Wheels A, D, and E are free to rotate independently on spindle O, while
B and C are compound and rotate together on spindle P, on the end of arm OP. All the teeth on different
gears have the same module. A, B, and C have 14 teeth, 32 teeth, and 16 teeth respectively, which are
cut externally.
a) Find the number of teeth on wheels D and E which are cut internally.
b) Determine the magnitude and direction of the angular velocities of arm OP and gear E If wheel A is
driven counterclockwise at 2 r.p.m while D is driven clockwise at 6 r.p.m., and the number of teeth of
gears E and D, are 78 and 62 respectively.
(Must use Tabular method) another method not accepted).
Steps
nber of
teeth
Step1
Step2
Arm OP
Gear A
Gear B
Gear C
Gear D
Gear E
A

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given parameter

VIEW

Step 2: Calculation 1st part

VIEW

Step 3: 1st part calculation continue

VIEW

Step 4: 2nd part calculation

VIEW

Step 5: 2nd part continue

VIEW

Step 6: 2nd part continue

VIEW

Solution

VIEW

Step by step

Solved in 7 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Design of Power Transmission Elements and Power Transmission Systems

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

i need the answer quickly
I need answer within 20 minutes please please with my best wishes
I need the answer as soon as possible
A worm drive transmits 15 kW at 2000 rpm to a worm gear having 90 teeth with 6mm module. The worm is triple threaded and has 65 mm pitch diameter. The tooth form is to be 20 degrees full depth involute. Determine: a) the lead and lead angle of the worm A. b) The center distance between worm and gear. c) The tangential force acting on worm. d) The axial force acting on worm e) The radial force acting on worm
Answer d and e
A planetary gear train is shown in the figure. The sun gear (gear 1) is fixed, it has a 1-in. pitch diameter with a diametral pitch of 12. Gear 3 has 36 teeth and gear 4 has 20 teeth. Gear 5 has 40 teeth and is keyed to the same shaft as gear 4. Gear 5 mates with the ring gear (gear 6), which serves as the output from the train and has 160 teeth. The carrier (link 2) serves as the input to the train, determine the rotational velocity of the ring gear when the input shaft rotates at 1125 rpm clockwise.
3. The center distance of two pair of meshing spur gears 4 = a, =160mm m, = m, z, = 20 3 = 30, 2, = 50 . Calculate the module of four gears and the tooth number of gear 1.
6. 5 3 Arm 6. 2 Arm Arm 2 3 1 Bearing Given N2 = 30, N3 = 25, N4 =45, N5 = 40, N6 = 200 W2 = 240 rpm ccw, warm = 120 rpm cw, T2 = 12 ft-lb Show your work. Answers without work will not be accepted a. Identify the gear sets. b. Determine the velocity gear train ratio and the angular velocity of gear 6. c. Determine the torque gear train ratio and output torque of gear 6.