Answered: Please find the following using the…

Please find the following using the graph provided. 1. Resilience (use calculated yield point) 2. Toughness please explain the calcualtion and equation needed.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: (3) Use the following graph to answer the questions on this page. The total time is 0.4 seconds.…

A: Solution:

Q: Neoprene material is an example of which of the following families of materials?: Elastomers…

A: This questions are based on the concept of material properties and material science

Q: Aim: To conduct a full kinematic analysis and calculate dynamic reaction forces in a linkage…

Q: 5. I went for a 2 mile bike ride. With the given information below, how many times did I pedal my…

A: Distance to cover S = 2 mile = 2 x 63360 inch = 126720 inPedal crank radius rp = 4.6 in , so…

Q: The following data were collected from a 0.4in. diameter test specimen of poly uinyl chloride…

A: Given To find -Tensile strength

Q: Develop a mathematical model of the performance of a plastic bonding process given the process data…

A: It is asked to generate a mathematical model to represent the table above

Q: untuitive methodology (seize and fox) noting they will be different. folowing cases, find the…

Q: components are represented by the supports in t

A: The supported beam has no bending moment at their extreme positions thereby only reaction forces are…

Q: During a football game, a vertebra in one of the player's spines experiences a shear force of 524 N.…

Q: explain the strain here? include the minimum and the max .

A: Given: To find: Explain the strain

Q: Concrete is a commonly used construction material. One of its deficiencies is a relative weakness…

A: to find:the stress in the steel and in concrete.given:the side of a square member of concrete is the…

Q: Points for stress vs strain (in image) Assume the compressive concrete strength (f’c) is 3,000…

Q: 6. For the following wire rope diameters of 6 x 19 type wire rope, with steel core, find the…

A: The list of all parameters related to 6×19 type wire rope, with a steel core is given as Now, take…

Q: Dosite figure he Centroids (X and Y axe nertia about the X and Y. tion about the X and Y a

Q: Match the following statements with the term that best describes each statement. (Enter Number ONLY)…

Q: A 2.5 cm diameter HDPE cord (whose properties Fig. 5 are listed in Fig. 5) that is initially 25 cm…

A: Given data is

Q: During the General Enhanced Community Quarantine, we were mandated to stay and work from home. We do…

A: Draw a diagram showing the five displacements at home. Here, 3 displacements are between the room…

Q: Name: Surname: Student ID: ME 216 MECHANICS OF MATERIALS QUIZ # 2 QUESTION σ (MPa) 490 420 350 280…

A: According to our guidelines, we are supposed to answer the first three sub parts, Please repost…

Q: Consider the mapping in 2-D only = X1 +7X2 = X1+ uz *2 = (1+e)X2 = X2+ Uz. (1) 1. In terms of y and…

A: As per honor code and answering guidelines I can answer 1st 3 subparts at a time.If you want other…

Q: figure five shows the tensile strength. The graph depicting stress (MPa) vs. stain ( percent ). The…

A: A stress strain diagram, also known as a stress strain curve, is a diagram that depicts the…

Q: prototype designs will be more efficient? cooled piston model both having the same diameter of five…

A: Considering air cooled modelInitial pressure at starting of compression (P1)=14.70 psiInitial volume…

Q: A5.1 Please help. Written on paper not typed on computer or keyboard please. Need help both…

Q: As the tempering temperature of a heat-treated steel increases, the associated values of Brinell…

A: 1. As the tempering temperature of a heat-treated steel increases, the associated values of Brinell…

Q: Calculation 1. Define torque. 2. Give the expression for torque. 3. Define modulus of rigidity.

A: given; 1.define torque2.give the expression for torque3.define modulus of rigidity

Q: 1. You are finding Young's modulus of a sample of wood, using the simply supported and centrally…

A: Disclaimer:Since you have asked multiple questions, we will solve the first one as per Bartleby…

Q: Which of the following simulations can be done as a rigid-body analysis? O 1) Checking whether a…

A: W can answer the first question since the exact one is not specified. Please resubmit the question…

Q: The graph below shows the yield stress for a polycrystalline metal as a function of the grain size…

Q: Show strain gage installation for Uniaxial Loading, Biaxial Loading, Pressure in pipe, Bending and…

Q: Use the middle of the 5 measurements for your calculations. Use the equation: azgsim( a-g sin(e) to…

Q: demonstrate 10) Torricelli's equation, in the form parameterized by the trajectory (make an…

A: given; 10) Torricelli's equation, in the form parameterized by the trajectory (make an illustration)…

Q: pipe carries deion is capped (Figure ed to the end of t

A: given:pressure P=50psid=0.75int=0.5in

Q: A steel cylindrical violin string that plays the "E" note: Length = 360 mm • Diameter = 0.25 mm…

Q: Consider the graph below for 3 test samples A, B and C of the same metal composition which have been…

Q: FOLLOW THESE STEPS FOR UPVOTE Given Required Diagram Solution Conclusion Do not round off while…

A: In this problem , the condition of Methane, propane & Hexane are given below.

Q: A Portable Crane will be designed as shown in Figure which is able to withstand dynamic loads. The…

Q: Question 1: For the following truss structure (with members AB, BC, AD, DE, BE, CF and FG all of 60…

Q: The prime characteristics of the MATLAB program should be: 1. The MATLAB code should show clearly…

Q: Consider the graph below for 3 test samples A, B and C of the same metal composition which have been…

Q: O A four-element model of springs and dashpots is better than a power-law equation in representing…

A: following is the correct answer to the above question-

Q: Recall that muscle generates force at 30 N/cm?. Two cross sections are taken from the rectus femoris…

A: Find the tendon force Given data:- Muscle force =30N/cm^2

Q: draw an ashby chart for a knife By using this instructured:

A: It is asked to plot an ashby chart for knife using the diagram below

Q: The deflection of a structural beam of constant cross section subjected to a transverse loading is…

A: It is asked to explain the reason for the possibility of M=EId2νdx2 to generate a solution for the…

Q: 10.19. An electrical-resistance strain gage records a strain of 400 µm/m on a steel tension member.…

Q: QI Find the mass matrix and stiffness matrix

Q: I asked for problems 6 and 7 to be answered, but I did not get a properly structured answered as the…

A: Chamfer the edge at 45o with 0.250” leg distance.

Question

Please find the following using the graph provided.

1. Resilience (use calculated yield point)

2. Toughness

please explain the calcualtion and equation needed. Thank you!

300
200
100
0-
0.5
1.0
1.5
2.0
2.5
e (%)

Expert Solution

Step 1

Given:

To find the resilience and toughness from the given graph.

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Similar questions

I need these three parts answered, if you are unable to answer all three parts please leave it for another tutor to answer, thank you.
Ql- mm ,length 40 mm. The final diameter 18 mm and length 45 mm. Draw the force-extension diagram and determine the following : a) Ultimate tensile strength, c) Modulus of elasticity, d) Percent elongation and e) Percent reduction in area. The following data collected from tensile test of a metal bar diameter 20 b) The fracture strength, Force - kN 75 90 | 105 120 131 125 110 25 50 4.7 Extension-mm 0.02 0.04 0.06 0.20 - 0.60 1.60 3.00 4.0 Fracture
Needs Complete typed solution with 100 % accuracy.
16. There are 4 materials that were exposed to different forces and their corresponding elongation is given. Which will have the greatest and lowest value of k. Material A was exposed to 100 N force and elongation is 0.02 meters. B was exposed to 200 N force and elongation is 0.05 meters. C was exposed to a force of 300 N and elongation is 0.07 meter, D was exposed to 400N force and elongation is 0.09 meter.
Physics In a simple supported beam , write the moment equation of the beam shown in this video if it is loaded with 10 kN/m uniformly distributed over the entire simple span of 4 meters and a concentrated load of 20 kN applied 2 meters from the left support. Present your answer using the GAPSA form by indicating all the given data, what is being asked in the problem, the appropriate formula, the entire solutions / calculations and the answer accompanied with corresponding unit of measurement. Thank you.calculate the moment equation and the segment ,using double integration method
Help me please
Q5
Machine Design
A piece of steel rebar is tested in tension to determine its mechanical properties. The length of the sample is 87.3 mm and the cross-sectional area is 52.1 mm². When stretched by 37.2 mm, the force measured is 14,884 N. At this point, the graph is non-linear, but no clear neck is visible. If the Poisson's ratio of the material is 0.281, calculate the cross-sectional area (mm²) at this point.
Please show all possible workings, such as how the matrix was derived and how the answer was reached. Use finite element analysis.
7. Which of the following is false: a. The coefficient of thermal expansion is larger if the bond energy is smaller b. Ceramics are generally ionic bonding c. Van der Waals bonding is generally stronger than covalent bonding d. The free electrons in metallic bonding is reason for electrical conductivity 8. Which of the following is true: a. Polymers are generally denser than ceranmics b. Young's modulus of ceramics are similar to polymers c. Composites have higher tensile strength than metals d. Ceramics have low resistance to fracture than metals
1.