Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 13 mm and an allowable normal stress of 130 MPa. Pipe (2) has an outside diameter of 50 mm, a wall thickness of 3 mm, and an allowable normal stress of 85 MPa. Assume x₁ = 3.9 m, x₂ = 1.3 m, and y₁= 3.2m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. = 3/₁ Answer: Pmax (1) i B (2) с kN

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 13 mm and an allowable normal stress of 130 MPa. Pipe (2) has an outside diameter of 50 mm, a wall thickness of 3 mm, and an allowable normal stress of 85 MPa. Assume x₁ = 3.9 m, x₂ = 1.3 m, and y₁= 3.2m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. = 3/₁ Answer: Pmax (1) i B (2) с kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250…

Q: The solid 1.85-in-diameter rod is subjected to a uniform axial distributed loading along its length…

A: We will calculate effective load at each section.

Q: Each of the four vertical links has an 8 X 36-mm uniform rectan- gular cross section, and each of…

Q: (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft

A: Given figure shows a copper pipe subject to uniformly distributed torque. It is required to find…

Q: -150 mm B - 300 mm 30°

Q: The copper pipe [G = 5,000 ksi] has an outside diameter of 3.750 in. and a wall thickness of 0.250…

Q: Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm •…

A: Given data Diameter of hole (do) = 2cm = 20 mm Width of plate (B) = 6 cm = 60 mm Un-axial tension…

Q: Problem #1. The figure below are 2 solid cylindrical bars joined together at point B. Find the…

Q: Q/For the state of plane stress shown: (a) Construct Mohr's circle, (b) Determine the principal…

Q: e average normal stress

Q: The solid 1.15-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: Two steel [E = 30,100 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe…

Q: A bar of the rectangular cross-section is 100mm thick by 50mm broad and carries an axial compressive…

Q: A hollow steel shaft with an outside diameter of 115 mm and a wall thickness of 11 mm is subjected…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: a B C

Q: A 0.2 in. 4 in. 2 in. В D |- – 3 in. + 2 in.→ P=6 kips В Find the average normal & stress on a-a.…

Q: The copper pipe [G= 8,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.125…

A: Given data, Copper pipe , G = 8000 ksi Outside diameter = 3.875 in Wall thickness = 0.125 in UD…

Q: in. The pipe is subjected to a uniformly distributed torque of t = 63 lb-ft/ft along its entire…

A: Given:Uniformly distributed torque, t=63 lb-ft/ft…

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.500 in. and a wall thickness of 0.250…

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250…

A: Use formula of Torsion Calculate maximum torque

Q: Question 6 of 15 The plate of thickness, t = 5 mm, is loaded with the following stress; o, =100 MPa,…

Q: Find maximum principal stress

A: Given data : The value of normal stress in X direction σX=-30 MPa The value of normal stress in Y…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: Determine the maximum stress of the plate.

A: Given, Determine the maximum stress of the plate. Rivet hole diameter.d= 2 cm Width,b= 6 cm…

Q: A solid 1.10 in. diameter shaft is subjected to a torque of T = 370 lb-ft and an axial load of P =…

Q: Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm •…

Q: Determine the maximum stress of the plate. • rivet hole diameter= 2 cm • width of the plate= 6 cm •…

Q: e pins are 1 cm in diameter and are made of 304 stainless steel. A distributed load of 200 N/m is…

A: Given:- two rigid bars with a 5cm x 5cm section A-36 steel. the pins are 1 cm in diameter a 304…

Q: (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a…

Q: a b 45 MPa 60° a

A: Given: Shear stress To find: Normal stress and principal stress on inclined plane

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 =…

A: F1=19Kips F2=33kips To find diameter of rod 2

Q: 1) The copper pipe below has an outer diameter of 50 mm, inner diameter of 30 mm, and G = 45 GPa. It…

Q: Two steel [E = 29,400 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

A: This question is related to the Strength of Material.

Q: The copper pipe has an outer diameter of 2.50 in and an inner diameter of 2.21 in . It is tightly…

A: Given:- The outer diameter of the copper pipe = 2.50 in The inner diameter of the copper pipe =…

Q: 2. In the structure below, the vertical bar A has a modulus of elasticity of 210 GPa, a length of…

Q: Question 1 of 5 /20 E View Policies Current Attempt in Progress The solid 1.05-in-diameter rod is…

Q: The solid steel rod (1) has an allowable shear stress of 13 ksi. The brass tube (2) has an allowable…

A: Determine the largest torque Tmax that can be applied at the upper end of the steel rod.

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 13
mm and an allowable normal stress of 130 MPa. Pipe (2) has an outside diameter of 50 mm, a wall thickness of 3 mm, and an allowable
normal stress of 85 MPa. Assume x₁ = 3.9 m, x₂ = 1.3 m, and y₁= 3.2 m. Determine the maximum load Pmax that can be supported by the
structure without exceeding either allowable normal stress.
=
3/₁
Answer: Pmax
(1)
i
B
(2)
с
kN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State of given data

VIEW

Step 2: Calculation of rod forces using Method of joints

VIEW

Step 3: Calculation of load in rod 1

VIEW

Step 4: Calculation of load in rod 2

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

5.
The solid 1.25-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 700 lb/ft. Two concentrated loads also act on the rod: P = 2100 lb and Q = 600 lb. Assume a = 12 in. andb= 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in. w -> A C a b Answer: Ox-8in. = i psi Ox-24in. = i psi
A hollow steel shaft with an outside diameter of 125 mm and a wall thickness of 15 mm is subjected to a pure torque of T = 3,100 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax (b) dmin = i i MPa mm
Problem 3.1. A 1-in-diameter solid bar (), a square solid bar (2), and a circular tubular member with 0.2-in. wall thickness (3), cuch supports an axial tensile load of 5 kips. (a) Determine the axial stress in bar (1). (b)lf the axial stress in each of the other bars is 6 ksi, what is the dimension, b, of the square bar, and what is the outer diameter, e, of the tubular member? I in. 1=0.2 in. (1) (3)
a.) In ksi b.) In rad
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) оp1 — 3940 рsi, Op2 -1980 psi, o p3 D0 (b) op1 = 83 MPa, o,2 = 60 MPa, O,3 = 0 Answer: (a) Tabs max psi = (b) Tabs max= MPa
Two steel [E = 29,500 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.500 in. and a wall thickness of 0.283 in. Pipe (2) has an outside diameter of 4.375 in. and a wall thickness of 0.204 in. Assume L₁= 15 ft and L₂= 25 ft. If the normal stress in each steel pipe must be limited to 18 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ Answers: (a) (b) Pmax VB= (1) = i i C B kips in.
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
A square bar AB with an allowable stress of 32 MPa is attached to a hollow tube BC. Compute the inside diameter of the hollow tube BC if the allowable stress is limited to 220 MPa. P. A B Cross Section of AB Cross Section of BC 50 mm ODI s0 mm 50 mm
The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown, determine the shear stress developed at points A and B. These points lie on the pipe’s outer surface. Sketch the shear stress on volume elements located at A and B. . The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and it is subjected to the uniformly distributed torque along its entire length, determine the absolute maximum shear stress in the pipe. Discuss the validity of this result.
Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.
The solid 1.55-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 775 lb/ft. Two concentrated loads also act on the rod: P = 1700 Ib and Q = 600 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x= 8 in. (b) x = 24 in. → - A В IC a Answer: Ox-8in. - psi Ox-24in. psi