The solid 1.55-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 775 lb/ft. Two concentrated loads also act on the rod: P = 1700 Ib and Q = 600 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x= 8 in. (b) x = 24 in. → - A В IC a Answer: Ox-8in. - psi Ox-24in. psi

The solid 1.55-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 775 lb/ft. Two concentrated loads also act on the rod: P = 1700 Ib and Q = 600 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x= 8 in. (b) x = 24 in. → - A В IC a Answer: Ox-8in. - psi Ox-24in. psi

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam is loaded by the couple M=2000 N-m as shown. The beam has a channel-type cross section as illustrated. 3 cm 30 cm 3 cm 3 m -2m1 10.5 cm BI 12 cm M. Determine the maximum tensile stress in the beam. O 1.60 MPa 3.73 MPa )2.49 MPa O1.07 MPa Determine the maximum compressive stress in the beam. 3.73 MPa O 1.07 MPa 2.49 MPa O 1.60 MPa Determine the maximum shear stress in the beam. O 00588 MPa 0.0490 MPa 0.0653 MPa O 0.0667 MPa
The green triangle (initial state) experiences deformation transforming into red triangle (final state). Determine the axial strain in side XZ if XZ = 655 mm and XZ' = 729 MM. (UNITLESS)
Knowing that the couple shown acts in a vertical plane, determine the stress at (a) point A, (b) point B. (a) GA= (b) B = +201 B. 40 20 Dimensions in mm MPa MPa 20 80 20 T N M = 12 kN - m
Determine the maximum stress of the plate. • rivet hole diameter 2 cm • width of the plate= 7 cm • uni-axial tension of 54 MPa
The plate of thickness, t 5 mm, is loaded with the following stress; o, = 100 MPa, o, = -60 MPa, E = 200 GPa, v 0.33. If a = 160 mm, and b= 200 mm, y C Calculate the change in the length (mm) of AB.
The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 60 MPa for the bronze segment AB and 84 MPa psi for the steel segment BC. Determine the diameter of each segment so that each material is simultaneously stressed to its permissible limit when the torque T = 40 kN-m is applied as shown. The shear moduli are 35 GPa for bronze and 80 GPa for steel. Bronze Steel B A T 3 m 2 m
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
Question # 4: Determine the state of stress at point A on the cross section at section a-a of the cantilever beam. Show the results in a differential element at the point. ( 2 m a 0.5m 400 KN 100 mm 300 mm 100 mm Section a-a
Find the minimum principal stress for the stress case given in the figure.
The thin rectangular plate is uniformly deformed such that Ex = 220E, Ey= -680 uE, and yy = 870 urad. If a = 35 mm, determine (a) the normal strain &, in the plate. (b) the normal strain &, in the plate. (c) the shear strain ynt in the plate. B D. a a a a a a a a a Answers: (a) En= i HE (b) Et= i HE (c) Ynt = i prad
The solid 1.05-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 800 lb/ft. Two concentrated loads also act on the rod: P= 2300 lb and Q = 1400 lb. Assume a = 12 in. and b = 24 in. Determine the normal stress in the rod at the following locations: (a) x = 8 in. (b) x = 24 in. → → -→ P B a Answer: Ox=8in. = psi Ox=24in. = psi
The solid 1.85-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w = 925 lb/ft. Two concentrated loads also act on the rod: P= 1700 lb and Q = 1100 lb. Assume a = 20 in. and b = 40 in. Determine the normal stress in the rod at the following locations: (a) x = 13 in. (b) x = 39 in. > > > -> -> > b Answer: Ox=13in. = psi Ox=39in. = psi