A hollow steel shaft with an outside diameter of 125 mm and a wall thickness of 15 mm is subjected to a pure torque of T = 3,100 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax (b) dmin = i i MPa mm

A hollow steel shaft with an outside diameter of 125 mm and a wall thickness of 15 mm is subjected to a pure torque of T = 3,100 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax (b) dmin = i i MPa mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Current Attempt in Progress A hollow steel shaft with an outside diameter of 125 mm and a wall thickness of 18 mm is subjected to a pure torque of T=7,200 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax = i MPa (b) dmin = i mm
Please provide complete and step by step solution.
A typical aluminum-alloy scuba diving tank is shown in the figure. The outside diameter of the tank is 165mm and the wall thickness is 15mm. If the air in the tank is pressurized to 18.0MPa, determine: (a) the longitudinal and hoop stresses in the wall of the tank. (b) the maximum shear stress in the plane of the cylinder wall. (c) the absolute maximum shear stress on the outer surface of the cylindrical wall. Answers: MPa MPa MPa MPa (a) Olong= Thoop= (b) Tmax= (c) Tabs max= Mi i i i
A hollow steel shaft with an outside diameter of 145 mm and a wall thickness of 19 mm is subjected to a pure torque of T = 4,800 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: MPa h mm (a) Tmax= (b) dmin =
how can i solve this one please
A solid 2.95 in. diameter shaft is subjected to a torque of T = 305 lb-ft and an axial load of P = 4700 lb. (a) Determine the principal stresses and the maximum shear stress at point Hon the surface of the shaft. (b) Show the stresses of part (a) and their directions on an appropriate sketch. N Answer: (a) Op1= i Op2= i A Tmax in-plane i H (1) psi psi psi T B (b) Show the stresses of part (a) and their directions on an appropriate sketch.
A circular steel tube of length L = 1.5 m is loaded in torsion by torques T (see figure). T r2 (a) If the inner radius of the tube is r, = 41 mm and the measured angle of twist between the ends is 0.5°, what is the shear strain y, (in radians) at the inner surface? (Enter the magnitude.) rad (b) If the maximum allowable shear strain is 0.00026 rad and the angle of twist is to be kept at 0.45° by adjusting the torque T, what is the maximum permissible outer radius (r,)may (in mm)? mm Enter a number.
A metal block (E = 60 GPa and Poisson's ratio of 0.35) rests on a rigid surface as shown below. It has uniformly applied loads which results in uniform stresses on the surfaces as shown. Assuming a compressive stress of 200 MPa along x-direction, determine the magnitude of stress oy for which the change in the height of the bock will be zero, (b) the corresponding change in the area of the face ABCD, and (c) the corresponding change in the area of the volume of the block. 40 2 100mm 25mm
8
S=25
#4 will upvote anyone who will answer
A hollow steel shaft with an outside diameter of 120 mm and a wall thickness of 10 mm is subjected to a pure torque of T = 6,100 N-m. (a) Determine the maximum shear stress in the hollow shaft. (b) Determine the minimum diameter of a solid steel shaft for which the maximum shear stress is the same as in part (a) for the same torque T. Answers: (a) Tmax= i (b) dmin= i MPa mm