Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 160 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 5 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 3.3 m, x₂ = 2.4 m, and y₁ = 3.9 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. A (1) (2) P KN

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15 mm and an allowable normal stress of 160 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 5 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 3.3 m, x₂ = 2.4 m, and y₁ = 3.9 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. A (1) (2) P KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250…

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 40 kN. Assume that a = 300 mm,…

Q: The solid 1.85-in-diameter rod is subjected to a uniform axial distributed loading along its length…

A: We will calculate effective load at each section.

Q: (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft

A: Given figure shows a copper pipe subject to uniformly distributed torque. It is required to find…

Q: The copper pipe [G = 5,000 ksi] has an outside diameter of 3.750 in. and a wall thickness of 0.250…

Q: Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm •…

A: Given data Diameter of hole (do) = 2cm = 20 mm Width of plate (B) = 6 cm = 60 mm Un-axial tension…

Q: The solid 1.15-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: Two steel [E = 30,100 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: a B C

Q: The copper pipe [G= 8,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.125…

A: Given data, Copper pipe , G = 8000 ksi Outside diameter = 3.875 in Wall thickness = 0.125 in UD…

Q: in. The pipe is subjected to a uniformly distributed torque of t = 63 lb-ft/ft along its entire…

A: Given:Uniformly distributed torque, t=63 lb-ft/ft…

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.500 in. and a wall thickness of 0.250…

Q: The copper pipe [G = 7,000 ksi] has an outside diameter of 3.875 in. and a wall thickness of 0.250…

A: Use formula of Torsion Calculate maximum torque

Q: The steel pipe AB has a 64-mm outer diameter and a 5-mm wall thickness. Knowing that arm CDE is…

Q: A cylindrical tank with hemispherical heads is constructed of steel sections that are welded…

Q: Determine the maximum stress of the plate.

A: Given, Determine the maximum stress of the plate. Rivet hole diameter.d= 2 cm Width,b= 6 cm…

Q: Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at…

Q: Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm •…

Q: The copper pipe [G = 8,000 ksi] has an outside diameter of 3.625 in. and a wall thickness of 0.250…

Q: For the link shown in the figure, the thickness of the link is 50 mm. Given that the force P= 40 kN,…

Q: Determine the maximum stress of the plate. • rivet hole diameter= 2 cm • width of the plate= 6 cm •…

Q: e pins are 1 cm in diameter and are made of 304 stainless steel. A distributed load of 200 N/m is…

A: Given:- two rigid bars with a 5cm x 5cm section A-36 steel. the pins are 1 cm in diameter a 304…

Q: The copper pipe shown in the figure has an outside diameter of 3.625 in. and a wall thickness of…

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

Q: Two steel [E = 29,400 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe…

Q: Question 1 of 5 /20 E View Policies Current Attempt in Progress The solid 1.05-in-diameter rod is…

Q: Pipe (2) is supported by a pin at bracket Cand by tie rod (1). The structure supports a load P at…

A: Given: Tie rodDiameter = 12 mmAllowable normal stress = 65 MPaPipe 2Outer diameter = 46 mmWall…

Q: A solid 2.40 in. diameter shaft is subjected to a torque of T = 330 lb-ft and an axial load of P =…

Q: The solid 1.25-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: The solid circular rod has a cross-sectional area of 470 mm². It is subjected to a uniform axial…

Q: The cross sectional area of the bar ABCD is 550 mm2. F1 = 25 kN, F2 = 20 kN, F3 = 35 kN. F1 F2 F3 Be…

Q: The copper pipe [G = 5,000 ksi] has an outside diameter of 3.750 in. and a wall thickness of 0.250…

Q: The d - 16-mm-diameter solid rod passes through a D=21-mm-diameter hole in the support plate. When a…

Q: Two steel [E = 29,500 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe…

A: Permissible normal stress in both pipe = 18 ksi E = 29,500 ksi Determinea. Maximum downward load P…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 15
mm and an allowable normal stress of 160 MPa. Pipe (2) has an outside diameter of 58 mm, a wall thickness of 5 mm, and an allowable
normal stress of 145 MPa. Assume x₁ = 3.3 m, x₂ = 2.4 m, and y₁ = 3.9 m. Determine the maximum load Pmax that can be supported by
the structure without exceeding either allowable normal stress.
A
(1)
(2)
Y₁
P
KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State the given data

VIEW

Step 2: Determine the maximum load

Step 3: Calculation

Step 4: Calculation

Solution

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
A square bar AB with an allowable stress of 32 MPa is attached to a hollow tube BC. Compute the inside diameter of the hollow tube BC if the allowable stress is limited to 220 MPa. P. A B Cross Section of AB Cross Section of BC 50 mm ODI s0 mm 50 mm
The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown, determine the shear stress developed at points A and B. These points lie on the pipe’s outer surface. Sketch the shear stress on volume elements located at A and B. . The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and it is subjected to the uniformly distributed torque along its entire length, determine the absolute maximum shear stress in the pipe. Discuss the validity of this result.
#11 Normal stress in rods 1 and 2
Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.
The solid circular rod has a cross-sectional area of 440 mm². It is subjected to a uniform axial distributed loading along its length of w = 9 kN/m. Two concentrated loads also act on the rod: P = 7 kN and Q=5 kN. Determine the normal stress in the rod at x = 0.4 m. Assume a = 0.5 m and b=0.9 m. a Answer: σ= i B MPa O
10. An Assembly shown below whereas a link BD consists of a bar with 1 in. wide and 1/2 in. thick. Considering that each pin has a 3/8 -in. diameter, Find the maximum value of the average normal stress in link BD given the conditions: (a) O = 0, (b) 0 = 900. 4 kips .6 in. 12 in. 30° D
a)jj holiow steel tube jsed in a roof structure has an outer diameter, d; = 104 mm and inner diameter, dz = 82 mm. The length of the tube is given by L = 2.75 m and has shear modulus, G = 28 GPa. If the tube is twisted in pure torsion by torques acting at the ends, distinguish the angle of twist when the maximum shear stress, Tmax = 48 MPa.
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.125 in. and a wall thickness of 0.286 in. Pipe (2) has an outside diameter of 4.000 in. and a wall thickness of 0.209 in. Assume L₁ = 13 ft and L₂= 21 ft. If the normal stress in each steel pipe must be limited to 24 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ Answers: (a) Pmax= (b) VB= (2) (1) tel i tel P C B kips in.
Solve alll subparts b, c, d and e B) determine the principal plane (for σmax) in radians. C) Determine the shearing stress in a plane, which is 330 with the vertical (clockwise). D) determine the normal stress (in MPa) in a plane, which is 330 with the vertical (clockwise). E) determine the minimum values of θ (in radians) for which the normal stress is the equal to or less than 35.2 MPa.
a.)For the given figure, determine the normal stress in MPa at segment AB, Cross-section of AB is 1500mm2. b.)Determine the normal stress in MPa at segment BC. Cross-section of BC is 2000mm2. c.)Determine the normal stress in MPa at segment CD, Cross-section of CD is 1200mm2.