Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 14 mm and an allowable normal stress of 125 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 6 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 2.9 m, x2 = 2.0 m, and y₁ = 4.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Y₁ (1) Answer: Pmax= i kN

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 14 mm and an allowable normal stress of 125 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 6 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 2.9 m, x2 = 2.0 m, and y₁ = 4.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Y₁ (1) Answer: Pmax= i kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bell-crank mechanism is in equilibrium for an applied load of P = 40 kN. Assume that a = 300 mm,…

Q: (a) the maximum shear stress in the pipe. (b) the rotation angle pc at the free end of the shaft

A: Given figure shows a copper pipe subject to uniformly distributed torque. It is required to find…

Q: The copper pipe [G = 5,000 ksi] has an outside diameter of 3.750 in. and a wall thickness of 0.250…

Q: The solid 1.15-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Q: in. The pipe is subjected to a uniformly distributed torque of t = 63 lb-ft/ft along its entire…

A: Given:Uniformly distributed torque, t=63 lb-ft/ft…

Q: The rectangular bar has a width of w= 2.75 in. and a thickness of t = 2.00 in. The normal stress on…

A: Given : W = 2/75 in. t = 2.00 in Normal stress on plane AB of the rectangular block is 6ksi

Q: Why is the force Fd pointing downwards? By force equilibrium, shouldnt it be 3 + Fd = 9 Fd =…

A: yes, you are right by equalibrium condition 3+Fd=9 we calculate reactions using the equailibrium…

Q: The copper pipe shown in the figure has an outside diameter of 3.625 in. and a wall thickness of…

Q: 1) The copper pipe below has an outer diameter of 50 mm, inner diameter of 30 mm, and G = 45 GPa. It…

Q: A solid 2.40 in. diameter shaft is subjected to a torque of T = 330 lb-ft and an axial load of P =…

Q: The solid 1.25-in.-diameter rod is subjected to a uniform axial distributed loading along its length…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 14
mm and an allowable normal stress of 125 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 6 mm, and an allowable
normal stress of 145 MPa. Assume x₁ = 2.9 m, x2 = 2.0 m, and y₁ = 4.4 m. Determine the maximum load Pmax that can be supported by
the structure without exceeding either allowable normal stress.
Y₁
(1)
Answer: Pmax= i
B
P
KN

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: State the given data

VIEW

Step 2: Determine the maximum load

Step 3: Calculation

Step 4: Calculation

Solution

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 11 mm and an allowable normal stress of 170 MPa. Pipe (2) has an outside diameter of 44 mm, a wall thickness of 5 mm, and an allowable normal stress of 150 MPa. Assume x1 = 3.7 m, X2 = 1.1 m, and y1 = 3.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress.
a.) In ksi b.) In rad
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 14 mm and an allowable normal stress of 125 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 6 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 2.9 m, x₂ = 2.0 m, and y₁ = 4.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. %/₁ (1) Answer: Pmax= Save for Later i 18 eTextbook and Media B (2) C kN Attempts: 1 of 3 used Submit Answer N C M Q M Q Nu О Nu Q Nu Qu Nu
The d = 16-mm-diameter solid rod passes through a D = 21-mm-diameter hole in the support plate. When a load P is applied to the rod, the rod head rests on the support plate. The support plate has a thickness of b = 11 mm. The rod head has a diameter of a = 32 mm, and the head has a thickness of t = 10 mm. The shear stress in the rod head cannot exceed 130 MPa, the punching shear stress in the support plate cannot exceed 90 MPa, and the bearing stress between the rod head and the support plate cannot exceed 145 MPa. Determine the maximum value of Pmax that can be supported by the structure. P Support Plate Rod Answer: Pmax i Hole diameter D Head KN
The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly secured to the wall at A and three torques are applied to it as shown, determine the maximum shear stress developed in the pipe. Let T1=66, T2 =11, T3 =26
Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.