Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 14 mm and an allowable normal stress of 125 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 6 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 2.9 m, x₂ = 2.0 m, and y₁ = 44 m. Determine the maximum load Pax that can be supported by the structure without exceeding either allowable normal stress. (1) Answer: Pmax = Save for Later 18 eTextbook and Media KN Attempts: 1 of 3 used Submit Answer Q N O N Q No Q Nu

Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load Pat pin B. Tie rod (1) has a diameter of 14 mm and an allowable normal stress of 125 MPa. Pipe (2) has an outside diameter of 52 mm, a wall thickness of 6 mm, and an allowable normal stress of 145 MPa. Assume x₁ = 2.9 m, x₂ = 2.0 m, and y₁ = 44 m. Determine the maximum load Pax that can be supported by the structure without exceeding either allowable normal stress. (1) Answer: Pmax = Save for Later 18 eTextbook and Media KN Attempts: 1 of 3 used Submit Answer Q N O N Q No Q Nu

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and a uniformly distributed torque is applied to it as shown, determine the shear stress developed at points A and B. These points lie on the pipe’s outer surface. Sketch the shear stress on volume elements located at A and B. . The copper pipe has an outer diameter of 2.50 in. and an inner diameter of 2.30 in. If it is tightly secured to the wall at C and it is subjected to the uniformly distributed torque along its entire length, determine the absolute maximum shear stress in the pipe. Discuss the validity of this result.
Find max and min stresses. Please provide step by step solution. Don't copy!!
Two steel [E = 30,300 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.125 in. and a wall thickness of 0.265 in. Pipe (2) has an outside diameter of 3.500 in. and a wall thickness of 0.206 in. Assume L₁ = 13 ft and L₂ = 19 ft. If the normal stress in each steel pipe must be limited to 20 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ (a) Pr max (b) VB= (2) (1) i i C B kips in.
A channel-section has the dimensions as shown. Consider a cantilevered beam subjected to an end force P. L = 100 cm a) iif cross-section las is used, determine its normal stress distribution. (a) (b) b) if you stack two las sections as a box, but leave a gap between them, two sections carry = loadings with the same distribution pattern. Try express the results. (C) 2ª L 2CM дом E 2ch weld
Determine the maximum stress of the plate. rivet hole diameter= 2 cm • width of the plate= 6 cm • uni-axial tension of 55 MPa.
Determine the absolute maximum shear stress for each of the following plane stress states for which the principal stresses are given. (a) op1 = 2700 psi, op2 = -2470 psi, Op3 = 0 (b) op1 = 44 MPa, op2 = 25 MPa, op3 = 0
Can someone please answer this? Thank you, in advance.
The copper pipe shown in the figure has an outside diameter of 3.000 in. and a wall thickness of 0.383 in. The pipe is subjected to a uniformly distributed torque of t = 87 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.50 ft, and c = 7.75 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. Answers: ccccccccc.com (a) TA= a (b) TB = i b i psi psi
Two steel [E = 30,700 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 6.125 in. and a wall thickness of 0.286 in. Pipe (2) has an outside diameter of 4.000 in. and a wall thickness of 0.209 in. Assume L₁ = 13 ft and L₂= 21 ft. If the normal stress in each steel pipe must be limited to 24 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a). L2 L₁ Answers: (a) Pmax= (b) VB= (2) (1) tel i tel P C B kips in.
The copper pipe shown in the figure has an outside diameter of 4.000 in. and a wall thickness of 0.363 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.00 ft, and c = 7.5 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. a b Answers: (а) ТА i psi (b) Тв- i psi
a.)For the given figure, determine the normal stress in MPa at segment AB, Cross-section of AB is 1500mm2. b.)Determine the normal stress in MPa at segment BC. Cross-section of BC is 2000mm2. c.)Determine the normal stress in MPa at segment CD, Cross-section of CD is 1200mm2.