PI-12 Fig.P1-12 shows an aluminum rođ ABC consisting of twoportions AB and BC rigidly joined at B. If the normal stress1s 120 MPa and the deformation of point C will not exceed3 mm, determine the largest force P which may be applied.E = 70 GPa.32 mm25 mmAB1.5 m1.0 mFig.Pl-12

Answered: PI-12 Fig.P1-12 shows an aluminum rođ…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a=2.1m (1) c = 2m b = 3.1m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES B dia. of rod 1: = 13mm dia of rod 2 = 11 mm
Use 32 in2 and 48 in2 cross-sectional areas for tensile and compressive members, respectively. Determine the axial stress in member CD in psi. (Numerical absolute answer only without units in 3 decimal places)
PLEASE ANSWER NUMBER 8.MECH 311(MECHANICS OD DEFORMABLE BODIES): PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
(1) by Given: P B (2) (3) ↑ D P=28 kN R = 38 kN Square Bars b₁ = 57mm 6₂ = 19mm b3 = 38mm WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS. R P Q =9 kN
The wood column is pinned at its base and top. Take E= 10 GPa and or = 15 MPa. (Figure 1) Figure 150 mm" 25 mm 25 mm 75 mm 75 mm 1 of 1 Part A If the eccentric force P = 11.8 kN is applied to the column, determine the maximum normal stress. Express your answer to three significant figures and include the appropriate units. TIGB = Submit Part B Value Request Answer Submit Units If the eccentric force P = 11.8 kN is applied to the column, investigate whether the column is adequate to support this loading without buckling or yielding. ? O The column is adequate to support this loading without buckling or yielding. O The column is inadequate to support this loading without buckling or yielding. Request Answer
Part 1. A composite assembly of length, L-375 mm, consisting of a steel (G-77 GPa) core (2) connected by rigid plates at the ends of an aluminum [G-35 GPa) tube (1) is shown. The aluminum tube has outside diameter D₁ - 50 mm and inside diameter d₁-30 mm. = 100 MPa, and the The solid steel core has diameter d₂-25 mm. The allowable shear stress of aluminum tube (1) is (rallow) allowable shear stress of steel core (2) is (Tallow)2= 135 MPa. Determine (a) the allowable torque T that can be applied to the composite shaft. (b) the corresponding torques produced in tube (1) and core (2). (c) the angle of twist produced by the allowable torque T. T D₁ L Calculate the polar moment of inertia, J₁, of the aluminum tube. Answer: J₁ (106) mm².
Calculate the stress parallel to the inclined plane AB. Report your answer as a positive number.Answer: τn⁢t= Enter your answer in accordance to the question statement ksi.
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 185 MPa, determine the minimum diameter required for each rod. Assume P = 79 kN and Q = 134 kN. %3D dz di B Answers: d1 = mm. d2 = mm.
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. A) Determine the magnitude of load P. Express your answer in kips (rounded to the nearest hundredths.) B) Determine the shear stress on plane AB. Express your answer in ksi (rounded to the nearest tenths.)
The steel bar shown has a 100 mm by 25 mm rectangular cross section. If an axial force of P = 180 kN is applied to the bar, determine the maximum normal stress (in MPa) acting in the bar. Note: Your submitted answer should not include units. 100 mm Answer:
i need the answer quickly
Show FBD

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

PI-12 Fig.P1-12 shows an aluminum rođ ABC consisting of two portions AB and BC rigidly joined at B. If the normal stress 1s 120 MPa and the deformation of point C will not exceed 3 mm, determine the largest force P which may be applied. E = 70 GPa.