3. Consider the relationship S = (v3)|VLl||ILI(cos0 + sin0), where VLL is the line-to-linevoltage phase and 'L is the line current phasor, and |*| indicates magnitude. Which of thefollowing statements is true?A. S is the per-phase complex powerB. This relationship can be used for both Y and 4 connected loadsC.factor angle 0 is the angle by which V, leads I,ThepowerD. None of Above

In this question we will write about complex power.

%3D 3. Consider the relationship S = (V3)|VLL||ILl(cos0 + sin®), whereVu is the line voltage phase and 'L is the line current phasor, and |*| indicates magnitude. Which following statements is true? A. S is the per-phase complex power B. This relationship can be used for both Y and 4 connected loads c. The power factor angle C. 0 is the angle by which V, leads I, D. None of Above

%3D 3. Consider the relationship S = (V3)|VLL||ILl(cos0 + sin®), whereVu is the line voltage phase and 'L is the line current phasor, and |*| indicates magnitude. Which following statements is true? A. S is the per-phase complex power B. This relationship can be used for both Y and 4 connected loads c. The power factor angle C. 0 is the angle by which V, leads I, D. None of Above

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

How to solve for a (+) Phase Sequence and (-) Phase Sequence? Give an example and explain the steps.
please do this one too. your answers are very clear and easy to follow!
Electrical load that draws current whose impedance varies throughout the cycle of the input ac voltage waveform is known as nonlinear load. True False
The following phasor diagram is: a. The phasor diagram of SG when it is running at lagging power factor b. The phasor diagram of SM when it is running at leading power factor c. The phasor diagram of SM when it is running at lagging power factor with the existence of RA d. The phasor diagram of IM when it is running at lagging power factor
Q2
4
Describe the concept of three-phase power in electrical systems and its significance in power distribution.
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
thats it
In the figure, bus 1 is the reference bus, V1 = 1.06 p.u and the angle is 0.. A load with active power= 100 MW and reactive power = 50 Mvar is connected to bus 2. The line impedance is z12 = 0.12 + j0.16 p.u on a base of 100 MVA. Start with an initial estimate of |V2|0) = 1.0 p.u and 820) = 0•. Find |V2| () (one iteration). 100 MW 212 = 0.12 + j0.16 ++ 50 Mvar Vị = 1.0/0° О а. |V2| (1) = 0.4 p.u. Ob. |V2| (1) = 0.5 p.u. Oc. |V2| (1) = 0.7 p.u. d. (1) = 0.8 p.u. е. |V2| (1) = 0.6 p.u.
Impedances Z1 = 5.83 at angle of -59 deg. and Z2 = 8.94 at an angle of 63.43 deg. are in series and carry an effective current of 5A. Determine the Power and power factor of the circuit indicating if it is leading or lagging.
1. Given the circuit below, the phase voltages are given by Van = 20040° Vrms. The source impedance is 5 + j7 per phase and the wire impedance is 8 +j10 per phase. Let the load impedance be Zy = 50 ohms. Find: Van Vin Ven a. II, and Ic b. c. VAN, VBN, and VCN, and VAB, VBC, and VCA Z₂ Z₂ Z₂ Zw Zw Zw B C le N