A single-phase a.c. distrībutor AB is fed from end A and has a total impedance of (0-2+j03) ohm. Atthefar end, the voltage V = 240 V and the current is 100 A at a p.f. of 0-8 lagging. At the mid-point M, acurrent of 100 A is tapped at a p.f of 06 lagging with reference to the voltage Vy at the mid-point.Calculate the supply voltage V, and phase angle between V, and Vg-[292 V, 2-6°)

Answered: Image /qna-images/answer/4acd9f84-26bf-4110-a530-db07e52f0344.jpg

uror Ab Hom end nas a fota Ear end, the voltage V, = 240 V and the current is 100 A at a pf of 0-8 lagging. At the mid-point M, a curent of 100 A is tapped at a p.f of 06 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and V [292 V, 2-6°]

uror Ab Hom end nas a fota Ear end, the voltage V, = 240 V and the current is 100 A at a pf of 0-8 lagging. At the mid-point M, a curent of 100 A is tapped at a p.f of 06 lagging with reference to the voltage Vy at the mid-point. Calculate the supply voltage V, and phase angle between V, and V [292 V, 2-6°]

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i need the answer quickly
Fast
Three series loads are drawing 20A ms current through a 60HZ source. Load 1 is an 400W, 0.8 lagging induction motor. Load 2 is a 500VA, 0.6 lagging power factor and load 3 is a 2 ohm incandescent bulb. What is the total VA of the combined load? What is the overall PF of the combined load? а. b. c. d. What RMS voltage is the combined load operating? What capacitor VAR must be installed in parallel to the combine load to improve its overall PF to unity? е. What is its approximate capacitance in microfarad?
help fast pls.
For the FET equivalent circuit in Figure 1, what is the value of the input impedance? Why is it open- circuited? Explain your answer? Vgs 8mVer so Figure 1
ASAP 20 minutes left
Please give the step-by-step solution and the formula used.
Q3) Answer one of the following questions a. For the following circuit below, find the RMS load voltage for (a=0, a=30, a=60, and a=90). 30 60 90 VLoad rms ILoad 20 Vs= rms Gate Drive R+L V Loud fs=50 Hz
A strain gage with gage factor of 2.75 and gage resistance of Rg=3702 and R=370Q2. If a strain of 1660 μm/m is applied as shown in the figure, Find: a) The new resistance of the strain gage b) The offset voltage if Vs = 10v. Vs R R Rg
i need the answer quickly
An impedance z₁ = 8j5ohms is in parallel with an impedance z₂ = 3 + j7ohms. If 100V are imposed on the parallel combination. Find the branch current 11, 12 and the resultant current. Draw the corresponding phasor diagram showing each current and voltage drop across each parameter. Calculate also the equivalent resistance, reactance and impedance of the whole circuit.
Consider the following circuit used to provide power for an inductive RL load. The input voltage is Vs=150V and the load has a 30 impedance value. The thyristor is working at a frequency fs = 2 kHz. The discharge current is to be limited to 50A and the required dv/dt is 50V/us. The values of Rs and Cs are equal to: Cs Ti V, Select one: O a. 30, 0.158µF b. 30, 0.352µF ос. 30, 0.64µF O d. 60, 0.5µF