An alternating current generator with a frequency of 500 Hz and a peak voltage of 120 V is connected with a resistor of R = 15 N, an inductor of L = 20 mH and a capacitor of C = 42 µC in series. a) Find the impedance and phase angle of the circuit. b) Find the peak voltages across the R, the L and the C individually. c) Draw the corresponding phasor diagram.

Q: 1. Give the temperature classification for solid insulating materials. Why is this classification…

A: It is asked to give the temperature classification for solid insulating materials. Also we need to…

Q: Thanks for your helping

A: It is our pleasure that you get what you were looking for.

Q: What is the voltage drop across RC, VC, in volts?  (Enter the number, not the units.)

A: Given circuit is -

Q: A PV module has been tested using a steady-state solar simulator, and the following I-V and P-V…

A: To extract the maximum power from the PV, there are multiple MPPT controllers are used nowadays P…

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: What is the meaning of semiconductors? Are the diodes can be counted as semiconductors?

A: Semiconductors are materials which have a conductivity between conductors (generally metals) and…

Q: brownout is defined as: a slightly decreased voltage lasting from seconds to minutes or more

A: In this question we will define brownout in power system....

Q: define the fake resistance

A: Fake resistance has property of some electrical circuit s and devices in which an increase in…

Q: 21/ Which Insulators can be used for both horizontal and vertical positioning? A. PIN TYPE…

A: Given  Which Insulators can be used for both horizontal and vertical positioning?

Q: L-march or T-match matching box

A: An L-match or T-match is a type of impedance-matching network used in radio frequency (RF) circuits…

Q: Name the type of wiring for the 3 wires proximity sensor shown below. BN Select one: O a. NPN…

A:

Q: A/An ________ captures different types of signals from the human body and convert them into…

A: The solution is given below.

Q: Grateful a little help with this homework thanks.

A:

Q: Write background information about  MOFs for Electrochemical Energy Conversion and Storage…

A: MOFs for Electrochemical Energy Conversion and Storage.

Q: (b) What are the FIVE (5) sources of errors of measurements when using Wheatstone Bridge (DC)?

A: Wheattone bridge is an electrical circuit which is used to measure the value of uknown resistance in…

Q: What is the acceptable minimum value of leakage current of HI-POT Test of electrical cables. Can you…

A: According to the question,what is the acceptable minimum value of leakage current of HI-POT Test of…

Q: Can a round 4 in. x 1/2 in. box marked as 8 cu in. with cable clamps supplied with 14/2 W/G NM cable…

A: Given data: Can a round 4 in. x 1/2 in. box marked as 8 cu in. with cable clamps supplied with 14/2…

Q: A 40 amp branch circuit is run a long distance requiring a voltage drop calculation which increases…

A: To determine the proper size for the copper equipment grounding conductor in a 40-amp branch…

Q: ity or enery that are used by

A: The power system consists of electric generation, distribution and customer satisfaction. In a…

Q: A. You are using 3 resistors (1000, 2.2kQ, 10KQ) in series, 3 LEDS are attached one after each…

A: Given, Using 3 resistors ( 100 Ω, 2.2 kΩ, 10 kΩ ) in series, 3 LEDs are attached one after each…

Q: Assume that the collector current changes from 2.5mA to a new level of 3mA. Determine the magnitude…

A: Given thatcollector current change from 2.5mA to 3mAfind magnitude of IC change %

Q: A simple circuit with one or more chips for Digital Integrated Circuits subject, with a written…

A: Integrated circuits: An Integrated Circuit (IC) is an electronic device that assembles (or…

Q: Compare the nested and the NPC topologies in terms of the blocking voltage for the switches employed…

A: We need to compare NPC and Nested topology.

Q: How do you prove the correct operation of a digital multimeter? Present your answers in tabulated…

A:

Q: Compare the nested and the NPC topologies in terms of the blocking voltage for the switches employed…

A: Concept- The nested and the NPC topologies in terms of the blocking voltage for the switches…

Q: Write the names and functions of the three devices used for circuit laboratory experiments and…

A: In this answer we will discuss about any three devices that are used in the laboratory for…

Q: included with the kitchen small appliance branch circuits?

A: There are many devices that can be included with the kitchen small appliance branch circuits

Q: Show a picture of t match and l match matching box. Which one would be better used for a PCB?

A: According to the question, we need to show a picture of T match and L match matching box. Also need…

Q: For an N channel E MOSFET what is the value of Id when VGS(TH)=3 V and Vgs(on)=4 V and k=1.5 mA/V2…

A:

Q: P-channel MOSFET is basically a following device. a. voltage operated O b. low-frequency operated O…

A: MOSFET is controlled by the application of GATE pulse .  GATE pulse controls the conduction state of…

Q: HERE IS IT

A: Physical address can be expressed by the following formula:Physical Address = (Segment Address) x 10…

Q: Mark the correct statement Select one: O a. Insulators are those materials that contain electrons…

A: The resistance of a material is directly proportional to the length of the material and inversely…

Q: Give brief answer only. Define DPST along with it's symbol and uses.

A: DPST switch: Definition with symbol? Uses?

Q: This is a general question: How do smaller electrical engineering labs relate to building a…

A: Smaller electrical engineering labs can be very helpful in building a relatively larger system. This…

Q: As an electrical and electronic engineer, your manager has asked you to write a report for the…

A: We need to write report on electric safety for different applications.

Q: I have an O Gauge track and would like to convert it into a “sensored” track. Additionally, I would…

A: According to the question, an O-gauge track and would like to convert it into a “sensored” track.…

Q: Draw bread board connection diagram for full adders along with tables and pin configuration of ICs…

A: Full adder truth table: Thus, Sum, S=X⊕Y⊕Cin and Carry, Cout = (X*Y) + ((X⊕Y)*Cin) So, the circuit…

Q: if you have (10) 10 OHM resistors and (5) OMR resistors in a series circuit what would the total…

A: Resistances are given as,

Q: in this Lab you will be laying out and installing an emergency service panel. Emergency service…

A: (1)  Legally Required standby systems provide electric power to selected loads during firefighting…

Q: The circuits branch is defined as: Select one: a. a single path in a network, composed of one source…

A: The circuits branch is defined as,

Q: If you dont have a vise to hold a EMT conduit what other two methods could you use to hold the EMT…

A: To hold the EMT conduit in place while cutting with hacksaw, following items or methods can be used…

Q: How Rth connected with the load resistance, explain

A: RL will be  connected in series with  RTH  as shown in the example.

Q: What is the specific procedure for clearing an EPROM for the first time

A: EPROM (Erasable Programmable Read-Only Memory) is a type of non-volatile memory that can be…

Q: Briefly explain the operation of the weighted resistor DAC.

A:

Q: Complete the wiring below, such that the two sensors are connected in series and capable of…

A: Two proximity sensors, one load and one power supply is given in the question. We need to complete…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.