% 11.+சالعنوان9:27>ہر개onlyJonShow that the critical speed of horizontal mold in true centrifugal casting can begiven as:30N₂ =√g/R۱/۱incluseostion|||[A]OI =T☑M

at critical speed of horizontal casting weight of casting (liquid metal ) = centrifugal force…

Answered: % 11. + ச العنوان 9:27 > ہر 개 only Jon…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Only answer question 4
Show that the critical speed of horizontal mold in true centrifugal casting can be given as: 30 N₁ = √g/R Π
A vertical true centrifugal casting process is used to produce bushings that are 200 mm long and 200 mm in outside diameter. If the rotational speed during solidification is 500 rev/min, determine the inside diameter at the top of the bushing if the inside diameter at the bottom is 150 mm? Ans. Dt = 167.98 mm.
1-In hot forming processes, the strain rate is important since deformation resistance of w.p. increases as is increased. ****** 2-The coating of interior surfaces of casting molds can aid....... 3- Based on nature of use, the cores can be classified into: 1. and 2. ..... and 4-In centrifugal casting, fine grain microstructure (resisting to corrosion, better mechanical properties) castings can be obtained because of...... 5-During manufacturing processes, the residual stresses can be arising due to three major reasons: 1......, 2...... and 3...... 6- The wheels, pulleys and flywheels can be manufacturing by...... casting. 7- The ...... of casting molds can help removing impurities and facilitating metal flow inside the molds. 8-In horizontal true centrifugal casting, a tubular products having uniform wall thickness can be obtained when...... is greater than ......
EX.3//A cylindrical riser must be designed for a sand-casting mold. The casting itself is a steel rectangular plate with dimensions 7.5 cm x 12.5 cm x 2.0 cm. Previous observations have indicated that the total solidification time (TTs) for this casting =1.6 min. The cylinder for the riser will have a diameter-to-height ratio=1.0. Determine the dimensions of the riser so that its TTS = 2.0 min.
: True centrifugal casting is performed horizontally to make large diameter copper tube sections. The tubes have a length= 1.0 m, diameter= 0.25 m, and wall thickness = 15 mm. (a) If the rotational speed of the pipe = 700 rev/min, determine the G-factor on the molten metal. (b) What volume of molten metal must be poured into the mold to make the casting if solidification shrinkage and contraction after solidification are considered? Solidification shrinkage for copper = 4.5%, and solid thermal contraction = 7.5%? %3D
Q no:10
: +0 usão العنوان on to A vertical true centrifugal casting process is used to produce bushings that are 250 mm long and 200 mm in outside diameter. If the rotational speed during solidification is 500 rev/min, determine the inside radii at the top and bottom of the bushing if R-2R. Take: -9.81 mis ۲/۱ ostrar
i need the answer quickly
Ex.1// A disk 40 cm in diameter and 5 cm thick is to be cast of pure aluminum in an open mold casting operation. The melting temperature of aluminum = 660°C, and the pouring temperature will be 800°C. Assume that the amount of aluminum heated will be 5% more than what is needed to fill the mold cavity. Compute the amount of heat that must be added to the metal to heat it to the pouring temperature, starting from a room temperature of 25°C. The heat of fusion of aluminum = 389.3 J/g... Assume the specific heat has the same value for solid and molten aluminum
What is the advantage in casting turbine blades that have either highly aligned grain boundaries or no grain boundaries at all?
True centrifugal casting is performed horizontally to make large diameter copper tube sections. The tubes have a length = 2.0 m, outside diameter = 0.4 m, and wall thickness = 30 mm. (a) If the rotational speed of the pipe = 600 rev/min, determine the G-factor on the molten metal. (b) Is the rotational speed sufficient to avoid "rain?" (c) What volume of molten metal must be poured into the mould to make the casting if solidification shrinkage and contraction after solidification are considered? Solidification shrinkage for copper = 3.5%, and solid thermal contraction = 6.5%.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

% 11. + ச العنوان 9:27 > ہر 개 only Jon Show that the critical speed of horizontal mold in true centrifugal casting can be given as: 30 N₂ = √g/R ۱/۱ incluse ostion ||| [A] O I =T ☑ M