Part A The stress-strain diagram for a steel alloy having an original diameter of 0.40 in. and a gage length of 9 in. is shown in the figure below. (Figure 1) Determine the modulus of elasticity for the material. Express your answer to three significant figures and include appropriate units. HA ? Eapprox = Value Units Submit Request Answer Figure < 1 of 1 Part B a (ksi) 80 Determine the load on the specimen that causes yielding. 70 Express your answer to three significant figures and include appropriate units. 60 50 HA ? 40 30 20 Py = Value Units 10 € (in./in.) 0 004 0.08 0.12 0.16 0.20 024 028 0 0.0005 0001 0.0015 0.002 0.0025 0.0030.0035 Request Answer Submit

Part A The stress-strain diagram for a steel alloy having an original diameter of 0.40 in. and a gage length of 9 in. is shown in the figure below. (Figure 1) Determine the modulus of elasticity for the material. Express your answer to three significant figures and include appropriate units. HA ? Eapprox = Value Units Submit Request Answer Figure < 1 of 1 Part B a (ksi) 80 Determine the load on the specimen that causes yielding. 70 Express your answer to three significant figures and include appropriate units. 60 50 HA ? 40 30 20 Py = Value Units 10 € (in./in.) 0 004 0.08 0.12 0.16 0.20 024 028 0 0.0005 0001 0.0015 0.002 0.0025 0.0030.0035 Request Answer Submit

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bar having a length of 125 mm and cross-sectional area of 467.5 mm? is subjected to an axial force of 40 kN as shown in (Figure 1). Part A If the bar stretches 0.03 mm, determine the modulus of elasticity of the material. The material has linear-elastic behavior. Express your answer to three significant figures and include the appropriate units. HA Figure E = Value GPa Submit Request Answer Provide Feedback 40 kN 40 kN 125 mm
The shear stress-strain diagram for an alloy is shown in the figure below (Figure 1). Take ✓ = 0.3 This is the info Figure T (ksi) || provided 0.004 y (rad) 1 of 2 Part A If a bolt having a diameter of 0.27 in. is made of this material and used in the lap joint, determine the modulus of elasticity E. (Figure 2) Express your answer to three significant figures and include appropriate units. Submit Part B HÅ Value Request Answer 3 μA P= 3.5.104 Provide Feedback Determine the force P required to cause the material to yield. Express your answer Units 3 o three significant figures and include appropriate units. ? ksi Submit Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining Enter your answer using units of US customary force. Pearson
How can I solve for the %0.2 offset strain and the calculated stress? Original diameter : 6mm Original length : 30mm Fracture diameter : 4.54mm
i need the answer quickly
Problem F2 stress (ksi) 130 120 110 100 90 80 70 60 50 40 30 20 10 0 0.000 0.025 0.050 0.075 0.100 0.125 0.150 0.175 strain (in/in) Above you will find the experimental stress-strain diagram of 1045 steel. Calculate the permanent set if a cylindrical specimen with a diameter of 2 in is loaded to the ultimate stress and then unloaded. Provide your answer in units of in/in with 3 significant figures after the decimal. The elastic modulus of 1045 steel is 29,000 ksi.
4. A titanium alloy (Ti-5Al-2.5Sn) specimen with the dimensions shown below is subjected to a uniaxial tensile load of 1500 N. (a) Determine if the deformation is entirely elastic. (b) What is the extension and gauge length (in mm) under this load? You may assume a Modulus of Elasticity of 110 GPa and a yield strength of 760 MPa. 13 mm 45 mm 9 mm R8 mm/ 40 mm
3. For a steel alloy, the stress-strain behaviour is shown below. Determine the modulus of elasticity, proportional limit, yield strength at 0.002 and maximum allowable load. 600 500E 400- 500 300 400- 300아 200 200- 100- 100E 0.000 0.002 0.004 0.006 Strain 0.00 0.04 0.08 0.12 0.16 0.20 Strain Stress (MPa) Stress (MPa)
Hi, I need help with this question.
A Brass specimen is subjected to a Tensile test in a laboratory. The following data obtained are: Length of Specimen = 367 mm; Diameter of Specimen = 19 mm; Yield Stress = 124 N/mm?: Ultimate Stress = 217 N/mm?: Fracture Stress = 183 N/mm?: % of Elongation = 50 % % of Reduction in area = 27 %. Determine the elongation at 103 kN, Load at yielding. Maximum load, Load at fracture, Final Length & Final diameter. Take Young's Modulus as 104 GPa.
Please show the complete solution. Thank you
The following data was obtained as a result of tensile testing of a standard 0.505 inch diameter test specimen of magnesium. After fracture, the gage length is 2.245 inch and the diameter is 0.466 inch. a). Calculate the engineering stress and strain values to fill in the blank boxes and plot the data. Load(lb) Gage Length (in) Stress (kpsi) Strain 0 2 1000 2.00154 2000 2.00308 3000 2.00462 4000 2.00615 5000 2.00769 5500 2.014 6000 2.05 6200 (max) 2.13 6000 (fracture) 2.255 b). Calculate the modulus of elasticity c). If another identical sample of the same material is pulled only to 6000 pounds and is unloaded from there, determine the gage length of the sample after unloading.
A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the proportional limit. Stress (ksi) 40 30- 20 10- 0- 0.0 0.0 Upper scale 0.020 0.002 22 ksi O 15 ksi E 19 ksi O 10 ksi 13 ksi Lower scale- 0.040 0.060 0.080 0.100 0.004 0.006 0.008 0.010 Strain (in./in.) 0.120 0.012