P3.12 The thin rod in Figure 3.43 always re- mains in contact with the leftmost cor- ner of the circular channel where r = R = 0.75m. At the configuration shown in Figure 3.43 the absolute angular speed of the rod is 1.6rad/s in the counterclock- wise direction. Find the velocity of point A on the rod at this instant. (answer: the magnitude of the velocity is 2.4m/s.) %3D

P3.12 The thin rod in Figure 3.43 always re- mains in contact with the leftmost cor- ner of the circular channel where r = R = 0.75m. At the configuration shown in Figure 3.43 the absolute angular speed of the rod is 1.6rad/s in the counterclock- wise direction. Find the velocity of point A on the rod at this instant. (answer: the magnitude of the velocity is 2.4m/s.) %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An aircraft wing is modelled by using a specific element type, which is defined by 2 nodes as shown below. Each node of this element has 3 Degrees of Freedom. If the total number of nodes, used for modelling the wing, is equal to 3,760 then calculate the total degree of freedom of the system. Node 1 Your Answer: element Node 2
please help me in number 1
write solutions please
Describe the Limit State Design?
Solve the Following Problem. JOB SEQUENCE "N" JOBS- "3" MACHINE JOB 1 2 4 A 10 6. 7 11 В 6. 2 3 4 4 9.
write Design spsecifcation for this system in small paragraphs
The mechanism shown in the figure controls the lifter. Calculate the reactions on CDE as the weight supported by the platform is W W(N)= 2800, L1(m)=0.6, L2(m)=0.6 , L3(m)=0.2 1) For three dimensional problems, please use vector notation.2) State what all the transactions you have done. All intermediate actions you have to doshow clearly.3) Please write the units next to the values you find.4) In the related questions, please draw the free body diagram.
examples, by conering them mer and then trying to draw the paral law, and thiking about how the sine and conine laws re sed to d the mknowns Then before solhing any of the problems, try and sntve some of the Fundamental Problems given on the next page. The solutiuns und answers to these are given in the back of the boik. Doing this throuphout the book will help immensely in developing your problem-solving skills 1%19 |. A 1:-1 lec.2.pdf 2.3 VECTOR ADDITION OF FORCES 27 FUNDAMENTAL PROBLEMS* F2-1. Determine the magnitude of the resultant force acting on the screw eye and its direction measured clockwise from the x axis F2-4. Resolve the 30-lb force into components along the r and raves, and determine the magnitude of each of these components 30 Ib ŽAN 6KN 12-1 F2-4 12-2. Two forces act on the hook. Determine the magnitade F2-5. The foroe = 450 Ih acts on the frame. Resolve this force into eomponents acting along members AB and AC, and determine the magnitude of each component. of the…
How can speed be attained from path function and time?
The input and output relationship of a process plant is given by: 3s+1 Y(s) = U(s) s3+9s2+26s+ 24 Identify the correct diagonal canonical form for the process plant system from the list below: (Note: You should select the correct answer number and also provide us with the calculation notes. Remember, all your calculation notes must be attached and uploaded as a separate document. It should be clean and readable with question numbers and their corresponding solution notes. Failure to provide this calculation notes could result in the candidate being awarded zero marks. Also, you may use MATLAB or any other calculation tools to cross-check answers should you wish to). O a. -2 0 0 x = 0 -3 0 x+1|u; y = [2.5 6 8]x 0 0 -4] O b. 4 0 0 x = 0 -3 0 0 -2] -0.31 0 x+ 0.3 u; y = [18 26 9]x [-0.3] O c. 4 0 0 -2.51 x = -3 0x+ u; y = [0 3 1]x 0 0 -21 -5.5 O d. None of the above
Part a and b
Learning Goal: To calculate the maximum allowable stresses in pressure vessels, compute the minimum allowable thickness of pressure vessels to meet certain constraints, and observe and compare properties of different pressure vessel shapes. Engineers are considering two possible vessel shapes for storing fuel. One shape is cylindrical and the other is spherical. Each vessel would be constructed out of the same material such that its hoop stresses and longitudinal stresses would be no greater than 120 MPa. The cylindrical pressure vessel has an inside diameter of de = 800 mm and a thickness of te = 25.0 mm. The spherical pressure vessel has an inside diameter of ds = 650 mm and a thickness of t = 11.0 mm. ▼ Part A - Maximum allowable pressure in the cylindrical pressure vessel Determine the maximum allowable pressure, pc,max, in the cylindrical pressure vessel. Express your answer in N to three significant figures. ► View Available Hint(s) Pc,max = Submit ΟΙ ΑΣΦ ↑ vec Previous Answers…