P. F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.

P. F- b 30 mm 50 30 mm mm Solution workout of this question with proper FBD has to be submitted in MS Teams. Please note down (screenshot) this question. A cutter is about to cut a cable with its jaws parallel as shown. The dimension b=0.071 m, and the applied force at the handles is F=17.4 N. Choose from the options below (a) the force on the cable, and (b) the force in the member PQ.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.12P: A differential equation encountered in the vibration of beams is d4ydx4=2D where x = distance...

See similar textbooks

Similar questions

Please don't provide handwritten solution ....
Inclined plane diagram: Also String 1 String 2 String 1 B C A The diagram above shows Carts B and C which roll without friction over an inclined plane. The plane is inclined at an angle of theta = 0 away from vertical, as shown in the diagram. Carts B and C are connected by an essentially massless string. Another massless string runs from Cart B over a massless and frictionless pulley to a hanging block, Block A.
A guy who works out at your gym found out that you are an engineer and has hired you do an analysis comparing two versions of a similar exercise: lateral raises. He wants to compare using dumbbells (as in Fig 1) versus using a cable machine (as in Fig 2). Develop an equation for each case for the moment about the shoulder as a function of angle. (0 to 90 horizontally) You will use your own dimensions for this analysis. You will need to measure: Arm length from shoulder joint to palm of your hand Height from shoulder joint to the ground Wingspan with arms held horizontally (palm-to-palm) You can use any measurements for the dimensions, just need the equations and FBD Fig 1: Dumbbell Lateral Raises Fig 2: Cable Lateral Raises
draw the fbd pls.
a) Pressure on the quay Weight of the container: Length of the reachstacker. Length of the arm 32 tons 4 meters 14 meters. Pls calculate the pressure on the quay. What is the 32 pressure on tons the quay Discover your What is the axle pressure on the front axle (which is standing on the quay)? ??d>www.nhtv1 Quay b) The volume of a 45° container is 86.65 m3. The internal measures are: - Length: - Width: 44'5" ft 8'5" ft What is the height of the container? c) You received 180*20ft containers and the standard ratio of 40ft containers. How much TEU did you receive?
Physics In a simple supported beam , write the moment equation of the beam shown in this video if it is loaded with 10 kN/m uniformly distributed over the entire simple span of 4 meters and a concentrated load of 20 kN applied 2 meters from the left support. Present your answer using the GAPSA form by indicating all the given data, what is being asked in the problem, the appropriate formula, the entire solutions / calculations and the answer accompanied with corresponding unit of measurement. Thank you.calculate the moment equation and the segment ,using double integration method
Statics Problem !!! Help me Part A and Part B!!!! Answer it this Problem Correctly!! Please give correct Solution
Lessons: Static of Rigid Bodies, Force Vector, Addition of a System of Coplanar Forces, Cartesian Vector, Etc. Kindly answer the following with complete solution. Please also draw the free-body diagram or illustration of your figure. Make sure to write with understandable hand-writing. Please send a clear picture of complete solution. I need the answer within an hour at least. I'll rate you with a like/upvote. Thank you.
FLUID MECH Support your answer with the appropriate solution and diagram. 3. A rectangular raft made of solid timbers (s=0.60) is 3 m wide and 6 m long x 60 cm thick. A man weighing 800 N steps on the edge of the at the middle of one of the longitudinal sides. Determine by how much the thickness of the raft will be depressed below the water surface along the side in mm. A. 10 B. 20 C. 30 D. 40
Need all parts in neat and clean handwritten solution.
A2.1 Please help. Written on paper not typed on computer or keyboard please. Need help both questions. Please include all units, steps to the problem and information such as its direction or if it is in compression or tension. Thx.
Use my ps5 slim for this task 96mm (height)x 358mm (width)x 216mm(depth) Or in inches 14.1 inches high, 8.5 inches deep and 3.8 inches wide. Weight is 7 pounds. Include all units and calculations. Thanks