6üzOyplanmadıOtüzerindenTxytlenmişoruyutleTntOxOn(a)(b)On the surface of a structural member, stresses are given as Oy=67,9 MPa, oy=25,5 MPa and Ty=-24,3 as shown in figure (a).Determine the magnitude of the maximum in-plane shear stress (MPa).Yanıt:

Given data: The stress in x-direction is σx=67.9 MPa The stress in y-direction is σy=25.5 MPa The…

Oy Ot Txy a Tnt Ox On (b) (a) On the surface of a structural member, stresses are given as ox=67,9 MPa, oy=25,5 MPa and Ty=-24,3 as shown in figure (a). Determine the magnitude of the maximum in-plane shear stress (MPa).

Oy Ot Txy a Tnt Ox On (b) (a) On the surface of a structural member, stresses are given as ox=67,9 MPa, oy=25,5 MPa and Ty=-24,3 as shown in figure (a). Determine the magnitude of the maximum in-plane shear stress (MPa).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

(b) Two round solid bars of different materials are connected in series against rigid supports as shown in Figure 4. Determine the stress in each bar and the support reactions if temperature is increased by 18º C. Bar A da, EA, aA Bar B dB, EB, aB LA LB Figure 4 Use the following information. Bar, B: Bar, A: Length, LB Diameter, de Poisson's Ratio Young's Modulus EB = 210 kN/mm² Coefficient of expansion ag = 12.4x106 °C-! = 25mm - 40 mm Length, LA Diameter, da Poisson's Ratio Young's Modulus EA = 70 kN/mm? Coefficient of expansion aa = 16.5x106 °C-1 = 10 mm = 0.28 = 30 mm = 0.32
A brittle material made of ASTM grade 30 cast iron has ultimate strength in tension of 31 kpsi and ultimate strength in compression of 109 kpsi and undergoes the following plane of stress state: o, = 20 kpsi and Tyy = 10 kpsi (CW). a) using the 3D Mohr's circle, find all three principal normal stresses. b) using the Brittle-Coulomb-Mohr theory and Modified-Mohr theory, find the factors of safety for the given plane of stress state.
Consider the state of stress in given figure where τxy = -37.4 Mpa. Solve the problem by method of equilibrium A) determine the normal stress component acting on the inclined plain AB B) determine the shear stress component acting on inclined plain AB
Q3: A steel rod is rigidly attached between an aluminum rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. BRONZE = 500 mm² 4P STEEL A = 400 mm² 2.5 m 2.0 m ALUMINUM A = 200 mm² P 1.5 m 2 2P
n the figure below, a member is subjected to an axial force P. If the cross sectional area of the member is denoted as AB, then the maximum value of its normal stress occurs when: ∅ = 00 ∅ = 300 ∅ = 450 ∅ =900
3. Listed below is a combination of stresses acting at a point and referred to axes x and y in an elastic material. Using Mohr’s circle of stress determine the principal stresses at the point and their directions for each combination. 1}sigmax -60 n/mm2 , sigmay -36n/mm2 ,TAUxy=5n/mm2 2}}sigmax 30 n/mm2 , sigmay -50n/mm2, TAUxy= 30n/mm2
The solid shaft is fixed in the wall at A (Figure Q2). A force F is applied at B, determine a) the stress components at points D and E, b) the principal stress at each of these points. (Draw free body diagram to show all loading forces and moments) Take F = 12 N and 0 = 45°. 1,25 mm 6 mm. 8 mm. 3 mm B F Figure Q2
pru 15 Oy enüz evaplanmadı Ot 00 üzerinden aretlenmiş Txy Soruyu aretle Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as Ox=67,9 MPa, oy=25,5 MPa and Tyy=-24,3 as shown in figure (a). If a=48,3 degree for the rotated element as shown in figure-(b), Determine the shear stress Tnt (MPa). Note: If the stress has negative direction, use - sign. Yanıt:
ru 8 бу enüz vaplanmadı Ot D0 uzerinden retlenmiş Txy Soruyu retle Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=61 MPa, oy=32,7 MPa and Txy=-28,1 as shown in figure (a). Determine the minimum principal stress (MPa). Note: If the stress is compressive, use - sign. Yanıt:
Grandpa/Shutterstock.com 7.3-26 An element in plane stress on the surface of an automobile drive shaft (see figure) is subjected to stresses of σ = -45 MPa and 7xy = 39 MPa (see figure). It is known that one of the principal stresses equals 41 MPa in tension. (a) Determine the stress o,. (b) Determine the other principal stress and the orientation of the principal planes, then show the principal stresses on a sketch of a properly oriented element. PROBLEM 7.3-26 T P o, Т 139 MPa 45 MPa
14 Oy iz planmadı Ot üzerinden Txy tlenmiş pruyu tle Tnt Ox On (a) (b) On the surface of a structural member, stresses are given as ox=67,9 MPa, Oy=25,5 MPa and Txy=-24,3 as shown in figure (a). If a=48,3 degree for the rotated element as shown in figure-(b), Determine the normal stress o (MPa). Note: If the stress is compressive, use - sign Vanıt:
The state of stress at a point in a structure is shown in the following figure.(a) find the main stresses (Show the results on a sketch ofcorrectly oriented).(b) Find the maximum shear stress with its average stress (Show theresults in a correctly oriented sketch).