A point on the surface of a mechanical component has the following state of plane stress o. = 90 MPa, oy = -50 MPa, and Tay = 60 MPa, see Figure 2: y| 50 MPa 90 MPa 60 MPa Figure 2 a) Draw Mohr's circle to represent this state of stress. b) Using Mohr's circle, determine the principal stresses and principal plane.

A point on the surface of a mechanical component has the following state of plane stress o. = 90 MPa, oy = -50 MPa, and Tay = 60 MPa, see Figure 2: y| 50 MPa 90 MPa 60 MPa Figure 2 a) Draw Mohr's circle to represent this state of stress. b) Using Mohr's circle, determine the principal stresses and principal plane.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q2: For the element shown in Figure 2. Use the data from Table 2 Determine the following: 1. The maximum and minimum principal stresses and their directions 2. The maximum and minimum shear stresses and their directions 3. The normal stresses acting with maximum shear stresses の→5ompa lompa => Txy 14 mpa
Give me right solution with clear calculations. Determine the normal and shear stresses that occur in the n-n plane of the figure. Present a diagram showing such stresses on the n-n plane.
4. The state of stress at a point, for a body in plane stress, is shown in the figure below. If the minimum principal stress is 10 kPa, then the normal stress oy(in kPa) is Gy 100 P (A) 9.45 (B) 18.88 (C) 37.78 (D) 75.50
i need the answer quickly
In a volume element with dimensions dx, dy, dz the negatíve y-face has a 2 MPa stress in the positivex-direction, a 3 MPa stress in the negative z-direction, and a 4 MPa stress in the negatíve y-direction. Which of the following describes the stresses per elasticity convention? Oyy = 4 MPa Oyr = -2 MPa 3 MPa A MPa
A) a state of stress at a point in a member defined by the element shown in the figure. Find the main stresses and their directions using the arithmetic method, as well as the equivalent vertical stresses on the inclined surface. 400 800. 1200 kg /cm b 400 kg /cm 800 kg/cm 1200
A point on a thin plate is subjected to two successive states of stress. The stresses have magnitude σx | = 31.5 MPa, |σy' | = 45.5 MPa, and |Tx'y' | = 20.5 MPa. 0x , Oy, Txy || = Determine the resulting state of stress on the element on the right. The rotation angles on the left-hand side of the figure are in relation to the orientation of the element on the right. Express your answers, separated by commas, to three significant figures. View Available Hint(s) 1977| ΑΣΦ | 11 VE 60° vec 220% ? Txy MPa, MPa, MPa ·0x
(b) Mohr's circle, invented by Christian Otto Mohr, is a graphical representation of the transformation law for the stress system. Use Mohr's circle to determine the stresses on an element inclined at 30° clockwise to the state of plane stress system as shown in Figure 1 and show the corresponding stress elements. Q2 (a) It is important im 80 MPa 50 MPa Ľ 50 MPa Figure 1 80 MPa 25 MPa
The state of stress at a given point is given in the following figure. Use Mohr’s circle to find: a) The principal stresses b) The maximum in-plane shear stresses. For both cases you must draw a rotated element including all stresses and the angle of rotation. You must draw a properly labeled Mohr’s circle.
The state of plane stress at a point on the surface of a cylindrical pressure vessel is shown in Figure Q2. Determine the following quantities using Mohr's circle (Remarks: You must show these stresses and directions in which they act on an elemental stress block): Q2. (а) 10 kPa 50 kPa 30 kPa Figure Q2 The stresses acting on an element oriented 40° counterclockwise from the position shown in Figure Q2. (i) (ii) The principal stresses. The maximum in-plane shear stresses and the orientation of the element which they act. (Remark: Elemental stress block is not required for upon this case). (iii) (b) Identify FOUR (4) differences between plane stress and plane strain transformation.
Relative to the x-, y-, and z-axes, the state of stress at a point in a component is found to be proportional to the matrix FIGURE P2.7 40-3 05 -3 2-3) Determine the normal, shear, and resultant stresses that act on a plane whose normal is inclined at 45° to the z-axis and the projection of the normal on the xy- plane makes 50° with the yz-plane (Figure P2.7). Find also the direction of the resultant stress. 40° 45 2 MPa 50⁰
The state of stress at a point in a structure is shown in the following figure.Determine:(a) The forces acting on an element oriented at an angle in the directioncounterclockwise angle = 40 ° from the x-axis (Show results in a sketch ofcorrectly oriented)(b) Find the maximum shear stress with its average stress (Show theresults in a correctly oriented sketch).