t = 400 mm 250 mm 300 mm

Q: A steel bar with length of 4.5 m is subjected to forces as shown in the figure: 1. Determine the…

A:

Q: The forces as given below are applied as shown in the figure. F1=10 kN, F2=5 kN and F3=3 kN. The…

A: a)  -159.15 MPa(Compressive) , 35.80 MPa(shear stress) b) Principle stresses 7.686 MPa ,-166.836 MPa…

Q: 1.2x 10-in. Undeformed Deformed EXAMPLE: 6. An initially rectangular element of material is deformed…

A: Draw the given diagram.

Q: 1.2 x 10-in. Undeformed Deformed B A An initially rectangular element of material is deformed as…

A: Normal strain: The ratio of the change in length to the initial length of any object in any specific…

Q: The state of strain at the point has components of €, = 180(10 6) €y = -100(10-6) and All attempts…

A:

Q: Elastic Recovery After Plastic Deformation A cylindrical specimen of a brass alloy 6.8 mm (0.27 in.)…

A: Stress is the ratio of force per unit area having the unit of N/m2 in SI system. Strain is the ratio…

Q: Q2 Figure Q2 shows a shaft consists of Rods AB, BC and CD which made of Aluminium. Brass and Steel,…

A:

Q: The system, which consists of solid circular bars, whose geometry and loading condition are given in…

A:

Q: A material is subjected to direct stresses (0) of equal intensity along the three mutually…

A:

Q: A very thick structure is subjected to certain traction boundary conditions on its surface. The…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: 1. A thin rectangular plate a = 20 mm x b = 12 mm (see figure below) is acted upon by a stress…

A: Given: To find: (a) The change in length of diagonal ACb) The shear strain, Yxv, along the length of…

Q: Given an element with stresses as indicated in figure below, find the following: a) The maximum and…

A: “Since you have posted a question with multiple sub parts, we willprovide the solution only to the…

Q: the direction where the normal stress is zero

A:

Q: 1) For the data given below, calculate the minimum value of the thickness of the object in the…

A: Given: The maximum allowed normal stress = 400 MPa The maximum allowed shear stress = 240 MPa The…

Q: In the figure, rigid bar ABC is support by a pin at B and by post (1) at A. However, there is a gap…

A: Length of post (1): L 1= 2.00 mThe gap between the rigid bar at A and post (1): Δ = 6 mmDisplacement…

Q: The principal stresses at a point P of an elastic body are (1) = 5 N/cm², o(²) = -5 N/cm² y o(³) =…

A:

Q: A steel bar of thickness h, to be used as a beam, is welded to a vertical support by two fillet…

A: Refer to the picture belowExplanation:

Q: Rockwell hardness . figure 6.19 Rockwell hardness Tensile strength = 0 MPA Tensile strength = 0 ksi…

A: (a)

Q: Find the shear stress (in psi) exerted on the member shown in the figure if load (V) = 55 6b kips…

A: Problem 1: Given data: Load, V = 55.66 kips = 55.66×1000 = 55660 pounds. Area, A = 105.85 in2…

Q: The rigid beam is supported a pin connection at A and a cable BD at point the. Diameter of pin at A…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: Complete the Circle of Mohr depicted in the figure.

A: According to the given details in the question.The Mohr Circle is Completed

Q: axial stress developed in the rod

A: Given data; Circular metallic rod of length, l =250 mmTemperature, T= 2000CYoung's…

Q: A thin metal alloy plate is loaded by biaxial stress (2 directions) given by 8000 psi in the x…

A:

Q: The gap of 0.5 mm in the element given in the figure is formed at 20 C. What is the temperature…

A: Given: ∆l=0.5 mml=0.45 mA=1800 mm2E=73GPaα=12.9×10-6 /°C

Q: Q1) At a point in a structure subjected to plane stress, the stresses are o = 4100 psi, Gy = 2200…

A:

Q: Q4 /B/ The stress-strain curve for four materials are shown in figure below. Which material…

A: From the stress - strain curve for the material C, it is observed that material C undergoes a large…

Q: For the truss in figure below, the cross-sectional area of the truss members is A = 500 mm² and…

A: Given data  Cross-section area(A) = 500mm2 The young's modulus(E) = 200(Gpa) The load (P)= 85.8(kN)…

Q: Given an element with stresses as indicated in figure below, find the following: a) The maximum and…

A: “Since you have posted a question with multiple sub parts, we willprovide the solution only to the…

Q: A circular bar of magnesium alloy is 750mm long. The stress-strain diagram for the material is shown…

A: Here at firstCalculating the total strain at point B by using the following relationεB=δLlHere εB ia…

Q: principal stress is 10 kPa, then the normal stress The state of stress at a point, for a body in…

A:

Q: For the steel block (Length L = 5-meter, Width W = 1 meter,  Height H = 1 meter) with compression…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.