OUTM showsuge UTM TM Figure 5 OUTM OUTMO Figure 5 showed applications of alloys as roofing materials (Figure 5a) and automotive body parts (Figure 5b). Suggest non-ferrous alloys that could satisfy each application. Justify your selection with the inclusion of comparison for mechanical strength requirements between both applications.

OUTM showsuge UTM TM Figure 5 OUTM OUTMO Figure 5 showed applications of alloys as roofing materials (Figure 5a) and automotive body parts (Figure 5b). Suggest non-ferrous alloys that could satisfy each application. Justify your selection with the inclusion of comparison for mechanical strength requirements between both applications.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Calculate the required voltage (V) if an unknown metal (M) was electrodeposited from an aqueous solution containing M2X2 (where X is the anion) with a supplied current of 4.05 A for 8 h, consuming 0.2411 kWh of electrical energy. Assume that the current efficiency is 90%.
Letter J only
Calculate the required voltage (V) if an unknown metal (M) was electrodeposited from an aqueous solution containing M2X2 (where X is the anion) with a supplied current of 5.66 A for 11 h, consuming 0.1727 kWh of electrical energy. Assume the current efficiency is 86%
Q3) Consider an extrinsic Silicon doped with Gallium atoms at a concentration of NA = 6.1016cm-3. The ionization energy for Gallium is given as 0.072eV. Calculate: a) The carrier concentrations po, no and the Fermi level EF- EF at T = 50 °Ke
Resistivity measurements at 300 K show that an annealed metal single crystal has amonovacancy concentration CV = 10-9. When the same crystal is quenched from a hightemperature, the measurements indicate CV = 2x10-3. Calculate the temperature of thequench [Take Hf = 51.4 kJ/mol and R = 8.314 J/mol.K]. State any assumption involved. (5)(b) Explain why the esistivity of a metal is expected to be found more at room temperature after quenching. Hint: Use Matthiessen’s rule (find out by self-studying and cite thesource.)
Calculate the mass (in grams) of K formed by a current of 6.5 x 104 A flowing for 24 hours if the electrolytic cell is 85% efficient. (At. Wt. K = 39.098)
Specific conductance is expressed in terms of Ohm- cm .a Ohm/cm .b O Ohm.cm .c O Ohm-1 cm-1 .d O
(8) VI. It took 1.00 hour for a 0.773 A current to plate 0.500 g of a metal containing M* ions. What is the metal?
In the In the old Weldon process, chlorine was made from by-product HCl by the reaction: MnO2 + HCl → MnCl 2 + Cl 2 + H2O Into a retort were charged 500 lb pyrolusite (86% MnO2) and 3500 lb hydrochloric acid (S.G. 1.098,20% HCl). The reaction was 92% complete. Determine (a) the limiting reactant based on mole ratio(b) lb Cl2 produced, (c) % excess reactant (d) % yield of MnCl2 if the actual amount of MnCl2 producedis 500lb. (MW: Mn=54.94, Cl = 35.45)
2) A 90.00 ml solution, density = 1.0582 g/mL. with a AG = specif ic heat of 4.079 J/(GC), increased in temperature ΔΗ- from 20.36 C to 28.13 t with Al added. The copper collected, weighed 2.087 g. The electrochemical AS = potential mean was +1.821 volts. Calculate AG AH and AS for the reaction below. +3 2A (aq) +2 2 Als) * 3 Cuaq) 3 C46)