|275 kN B (a) Knowing that o =160 MPa and 7 =100 MPa, select the most economical metric wide-flange shape that should be used to support the loading shown. (b) Determine the values to be expected for Om, Tm, and the principal stress omax at the junction of a flange and the web of the selected beam. D | 275 kN -3.6 m - 1.5 m 1.5 m For (b) check at Points B and C

|275 kN B (a) Knowing that o =160 MPa and 7 =100 MPa, select the most economical metric wide-flange shape that should be used to support the loading shown. (b) Determine the values to be expected for Om, Tm, and the principal stress omax at the junction of a flange and the web of the selected beam. D | 275 kN -3.6 m - 1.5 m 1.5 m For (b) check at Points B and C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1060 mm?. Assume a = 1.6 m, b = 9.8 m, andc = 3.6 m. If P = 60 kN and Q = 85 kN, determine the normal stress in each member. P В Q< b. Answers: OAB = i MPa (С) OBC = i MPа (Т) OAC i MPа (Т)
PLEASE ANSWER QUICKLY
3. A solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having cross- sectional area of 150 mm x 310 mm to the median line of the cross-section. (a) Determine the required thickness of the tube so that the maximum shear stress in the tube will not exceed the maximum shear stress in the solid bar. (b) Determine the shear stress in the tube . If it is subjected to a torque T = 15 kN-m and a thickness of 10 mm. and (c) Determine the angle of twist in degrees of the tube if the length of the tube is 1000 mm and the shear modulus is 75 GPa. Thickness of the tube is 10 mm and the torque T = 15 kN-m.
Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 2.5 kN. The crankshaft dimensions are b1 = 80 mm, b2 = 135 mm, and b3 = 55 mm. The diameter of the upper shaft is d = 26 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. | Yo B b3 Lütfen birini seçin: a. -155.971 MPa b. -200.302 MPa c. None d. -520.946 MPa e. -124.141 MPa
For the truss and loading shown, determine most economical cross-sectional area (in in2) of member DG, if P = 32628 lb, Q = 35720 lb, y = 6.18 ft, and the stress in the member is 5.45 ksi . Round off the final answer to three decimal places.
A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.7 in.². Assume a = 3.25 ft and b = 3.90 ft. If the normal stress in each member must not exceed 35 ksi, determine the maximum load Pmax that may be supported by the structure. A B b b Answer: Pmax= kips
A uniform cross section rod is composed of an aluminum section rigidly attached between steel and bronze sections. Axial loads are applied at the positions indicated.If P = 5.8 kN and the allowable stresses on the steel, aluminum and bronze are 40 MPa, 30 MPa and 25 MPa, respectively. Determine the minimum safe diameter for the rod. Answer: d= ___________________
The screw of the clamp exerts a compressive force of 250 lb on the wood blocks. The cross section is rectangular, 0.75 in. by 0.50 in 4 in. 0.75 in. a Part A Determine the maximum normal stress along section a- a. Express your answer to three significant figures and include appropriate units. HA ? Omax = 52.8 ksi
X Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If the normal stress in each rod must be limited to 170 MPa, determine the minimum diameter d2 required for rod (2). d₂ d₁ 140 KN 80 KN 140 KN C A ↑ 45.5 mm 49.0 mm O 35.3 mm 38.7 mm O 53.8 mm B
Current Attempt in Progress A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1580 mm². Assume a = 2.4 m, b = 8.2 m, and c = 3.5 m. If P = 60 kN and Q = 75 kN, determine the normal stress in each member. Lx Answers: JAB = OBC || MI MI JAC = i a P b MPa (C) MPa (T) MPa (T)
1200 N 2. For the bone shown to the left, assume the cross-section at C can be approximated as annular, with an outer diameter of 25mm. When the 1200 N forces are applied, the average normal stress in the bone at point C is determined to be 3.80 MPa. Determine the inner diameter of the bone cross section at C. Ans: d; = 14.93 mm 4 in. P 3 in. B 1200 N "UI 8
2. Given a front hand brake of a bicycle. The applied force, P = 70 N and the equivalent area and length of the cable is 1.02 mm² and 460 mm respectively. If the elongation of the cable is found to be 0.225 mm, find the normal stress in the cable. a. 137 b. 153 Brake cable, L = 460 mm 37.5 mm 50 mm Hand brake pivot A -100 mm- C. 168 d. 195 P (Resultant of distributed pressure) - Uniform hand brake pressure