| %17 elearning.yu.edu.jo a Time left 163:16:23 Question 1 Not yet answered Marked out of 4.00 (CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 144 (kips) is applied. The light rigid bar ABCD is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free. Steel L = 3 ft A = 0.5 in? E = 29 x 10° psi C 4 ft A Aluminum L = 4 ft A = 0.75 in? E = 10 x 10° psi P E 2 ft 2 ft → II

| %17 elearning.yu.edu.jo a Time left 163:16:23 Question 1 Not yet answered Marked out of 4.00 (CLO 1, 2)Determine the stress in the Aluminum rod (Psi) after the load 144 (kips) is applied. The light rigid bar ABCD is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free. Steel L = 3 ft A = 0.5 in? E = 29 x 10° psi C 4 ft A Aluminum L = 4 ft A = 0.75 in? E = 10 x 10° psi P E 2 ft 2 ft → II

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears a determine the minimum force P required to punch the slot. Punch O 1051 KN O 766 kN O 649 kN O 717 KN O 979 KN Slug Plate 20 mm 75 mm Plan view of slug + a stress of 360 MPa,
Solve it asap pl
A force of 100N is applied to the free end of a restrained beam, shown in the figure. The wall thickness is 2 mm from the upper and lower walls (1-6, 2-3, 4-5) and 4 mm on the side walls (1-2, 5-6). Calculate the normal stress distribution and the maximum stress in the middle section.
NOTE: The standard pull of the tape is 5kg while the team pulled only at 4kg The field temperature is 300 while the standard temp of the tape is 200 The cross sectional area of the tape is 0.05cm2. The coefficient of linear expansion is 0.000011610C and the modulus of elasticity of steel is given to be 2.0 x 106 kg/cm. The tape used here is a 50m steel tape. Determine the actual length of each lines
Question 5 of 15 The plate of thickness, t 5 mm, is loaded with the following stress; o, - 100 MPa, o, - -60 MPa, E- 200 GPa, v = 0.33. If a 160 mm, and b 200 minn, D. ► X A Calculate the change in thickness (mm). Select the correct response:
Engr. Sova Ho used 30m length of tape in measuring a distance line. The measured length of the line was recorded to be 454.62 m. During the measurement the temperature reading was 11 oC and the tape was supported at both ends. The cross sectional area of the tape is 6.50mm2 and the modulus of elasticity is 200 GPa. The tape has a weight of 0.075 kg/m. K= 11.6 x10-6 m/c. If the engineer determined the Temperature correction, Pull correction, and Sag Correction lengths to be 1,640.01 μm, 588μm, and 1.71 mm respectively, per segment. Calculate the applied Pull of the 30m tape in kg.
Please answer only number 1 with complete solution (all computations must be 4 decimal places)
Problem 04.107 - Maximum load carrying capacity of a milled rod with known allowable stress A milling operation was used to remove a portion of a solid bar of square cross section. Knowing that a = 30 mm, d = 20 mm, and all = 54 MPa, determine the magnitude P of the largest force that can be safely applied at the centers of the ends of the bar. The magnitude P of the largest force that can be safely applied at the centers of the of the bar is KN.
1. The 6061-T6 aluminum shaft shown below is loaded axially. The output from a strain gage mounted on the side of the shaft is 197.6 us in other words it has an axial strain of 1.976E-4 in/in. Determine the (a) direct normal stress o, (b) load P, (c) change in length AL, and (d) change in diameter. -11.28 in. Dia SG -lo = 384.6 P
Help me asap. a 50m long bar lacks 10mm to fit exactly between two fixed supports at 15 deg C. The modulus of elesticity is 230GPa and the coefficient of thermal expansion is 0.0000117/deg C. Find A. The normal stress if the temperature increased to 55 degree Celsius B. Calculate the height of the projectile from the ground after 15 seconds. C. What is the temperature if after thermal expansion, the stress in the bar is 50MPa D. What is the temperature if after thermal expansion, the bar exactly fits between the two supports? E. Calculate the total deformation of bar if at 55 degree C, the bar will exactly fit between the two fixed supports.