350mmi The simply supported beam has an l-shaped cross section. (1) Determine the values and locations of the maximum tensile and compressive bending stresses. (2) Sketch the bending stress distribution over the cross section on which the maximum bending stress occurs. No credits if free body diagram is not present. O 35m 8 kN/m 100 kN 11mm 7.5mm- 11mm 0.8 m 14 1.m 175mm |100KN

350mmi The simply supported beam has an l-shaped cross section. (1) Determine the values and locations of the maximum tensile and compressive bending stresses. (2) Sketch the bending stress distribution over the cross section on which the maximum bending stress occurs. No credits if free body diagram is not present. O 35m 8 kN/m 100 kN 11mm 7.5mm- 11mm 0.8 m 14 1.m 175mm |100KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The singular force F will be applied to the kin with a hollow rectangular cross section. Accordingly, the location and value of the minimum normal stress that will occur in the whole beam is given correctly in the following? F-800 N. L1 - 4m, 12 - 1m, h1-48mm, h2 -72mm, b1-10mm, b2-20mm
At which point on the design P-M interaction diagram is the design flexural strength largest? O Pure compression Pure tension Balanced failure point (CCL limit) O TCL limit Beam condition (Pn = 0) %3D //img00.zhaopin.cm
Quiz/ find the angle of rotation of the free end for the beam shown, then find the max sheaving stress If you know GAI = 28 GN/m² Gst=83 GN1m² GBV = 35 GN/m² Aluminum steel Bronzer Do d=100mm 3m d=75mm 2m 1.5m 1.5 KN.m
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
D) If the diameter of the cross-section of the beam is 500 mm compute for the maxumum shearing stress E) ss
Only ?% correct solution
Compute the maximum tensile and comprsive stresses devloped in the beam that is loaded and has the cross-sectional properties shown in fig 8 KN 120 mm 10 KN/m ΝΑ A 1=20 x10 6 mm4 4m B C 1m 50 mm
A steel beam is 24 inches tall, has a length, L, of 32ft, and has a yield stress of 36ksi. The simply supported beam supports a single load, P, of 17 kips at its midspan. If the theoretical maximum deflection of this beam is -(PL^3)/(48EI), determine the required moment of inertia such that the actual deflection of the beam will not exceed a value of L/360, and the actual stress will have a factor safety of 1.5 with respect to yielding.
Consider the following riveted joint. a) Find the total shear load on each of the three rivets b)Compute the significant rivet shear stress and bearing stress. c) Compute the moment of inertia of the 10 mm plate on a section through the three rivet holes and find the maximum bending stress in the plate.
3. For the beam with cross-section shown: a. Determine the maximum tensile stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). b. Determine the maximum compressive stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). c. Determine the maximum shear stress, and indicate which points experience this stress (tell which cross-section feels this stress, and which points on that cross-section feel this stress). d. For the cross-section 2 m to the right of A, determine the normal stress at point D on the cross-section, and state whether this stress is tensile or 100 KN m compressive. e. For the cross-section 2 m to the right of A, determine the shear stress at point D on the cross- section. f. Determine the equations for the elastic curve, and for the slope of the elastic curve, for…
1) will upvote anyone who will answer