Consider the following riveted joint.  a) Find the total shear load on each of the three rivets b)Compute the significant rivet shear stress and bearing stress. c) Compute the moment of inertia of the 10 mm plate on a section through the three rivet holes and find the maximum bending stress in the plate.

Q: eformation sustained by members CG, AF, 12 kips

A: Given:- 8 kips,12kips To find:- deformation sustained by members CG,AF,FG

Q: Prob 1. The rigid bar below is supported by a pin and two rods and must support a load of 100 kN is…

A: Modulus of elasticity of brass, Cross section of brass, Modulus of elasticity of copper, Cross…

Q: The lap joint shown is fastened by 6 − 20mm diameter rivets. Assuming that ? = 200??, determine (a)…

A: a.) The expression Shearing stress in each rivet is given as Ss=PAs Substitute the value in above…

Q: The hanger is supported using a rectangular pin. Determine the magnitude of the allowable suspended…

A:

Q: y M= 150 kip-in. |-6 in--6 in.- I 2 in. 8 in. C- 60° 2 in.- E

A: Calculating the  distance of neutral axis from the top of the section:…

Q: 1.60 Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A:

Q: 1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter…

A:

Q: Three plates are welded together to form the section shown. Dimensions of the cross section are b =…

A: Given: The value of b is 3.6 in. The value of d is 10.8 in. The value of a is 2.3 in. The value of t…

Q: 3. For the given structure and boundary conditions, what is the allowable load Pallow if the…

A:

Q: The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear…

A: Given data in question Load 750 kN Diameter 32 mm To find out  Permenant strain

Q: Two plates with a thickness of 35mm, width of 160mm, and length of 200mm are joined ogether by a pin…

A: thickness =35mm Width =160mm Length =200mm Pin Diameter =60mm

Q: 8 kN 4 m 15 kN 5 kN 2 m 2 kN 2m 2m A B с D E The aluminum rod shown has a diameter of 20 mm and is…

A: Given: diameter, D = 20 mm E = 70 GPa

Q: Problem 4 The joint is fastened together using two bolts. Determine the required diameter of the…

A:

Q: . For the riveted connection shown in the figure using  elastic analysis a. Determine the safe value…

A: Diameter of rivet = 25 mmAllowable shear stress = 150 MPaloading = 50 KNOther Data are given in the…

Q: COMPUTE THE SHEARING STRESS IN THE PIN AT B FOR THE MEMBER SUPPORTED AS SHOWN IN THE FIGURE. THE PIN…

A:

Q: If the applied load "P" causes the point C to be displaced downward by &c=1 mm, determine the normal…

A: LAC = 210 mmLBC = 480 mm

Q: The pinned joint shown here is held by a 1-cm-diameter pin. The thickness of the two members are t₁…

A: Given, Pin diameter (d) = 1 cm or 10 mm Thickness of plate 1, t1 = 0.5 cm or 5 mm Thickness of plate…

Q: Link AB is to be made of steel for which the normal stress is 450 MPa. Determine the cross-sectional…

A:

Members with compression and bending

Compression members are structural elements that carry compressive axial force. They are the vertical members of a building that support beams and their design, which is governed by buckling and strength. Columns are known as struct or compression members, which are subjected to compressive forces. These members provide stiffness to the building and avoid any imperfection regarding the transfer of axial load. For instance, webs in a truss, braces in a framed structure, tiers, and so on.