QN 47 A link of S-shape made of a round steel bar is shown in Figure. It is made of plain carbonsteel 45C8 (Syt = 380 N/mm2) and the factor of safety is 4.5. Calculate the dimensions of thelink.(d = 23.38 mm)1 kN1 kN Ad

Answered: Image /qna-images/answer/b228d7c4-7377-4b15-b93e-811cace996ea.jpg

Answered: ON 47 A link of S-shape made of a round…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A frame is shown to the right. The link BC is t = 6mm thick (into the page) and has width, w (that is, the cross section of the link is t by w). The link is made of steel, with an ultimate strength of 450 MPa in tension. What is the required width of the link if the frame must support a load of P = 20 kN, with a factor of safety equal to 3. (Hint: BC is a two-force member.) Ans: w = 27.8 mm 600 mm. A 480mm 5 in.
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. If load P = 23.5 kips, determine the normal force in bar (1). A 6 ft 49.9 kips 39.2 kips 41.5 kips 31.9 kips 23.7 kips D B (1) 4 ft P
The metallic hollow pipe shown in Figure Q1 is fixed at both its ends, and is under axial compression. The pipe has an external diameter D = 74 mm, an internal diameter d = 49 mm, and a length L = 5.06 m. The Young's Modulus of the metal used to manufacture the pipe is: E = 157.59 GPa. Figure Q1 Calculate the critical buckling load Pcrit using Euler's Formula. Assume the critical buckling load obtained through your calculations is valid in this case, and does not require verification. Use π = 3.14159 if needed. Express your answer in the unit: Newton (N). Report your answer to 2 decimal places.
Solve
last digit of matrix no is (8) fifth digit of matrix no is (0) so A;8 and B;0
Give the following problem a try. If you get stuck, here is one way to work it: Essential Solution Video. If load P = 19.6 kips, determine the normal force in bar (1). D P A 6 ft 32.7 kips 41.7 kips 38.8 kips 34.5 kips 45.4 kips B (1) 4 ft
Consider the frame shown in Fig 4. A 100N load is suspended around a fixed drum with radius 2 m There are 5 bars and u-.5, Point B is supported by a pin, while point E is supported by a roller. total. Using the Method of Joints (at Joint B) Find the loading in DB and CB. Loading DB = Loading CB = 10 3- G in in -1 4 E 8 T/C T/C 0.2 100 N
In the structure shown below (Figure 3), two forces of equal magnitude (P) are applied along the horizonal and vertical directions at point C. The beams are connected by pins at A, B and D. The pins A, B and D have diameters of 8 mm, 12 mm, and 14 mm, respectively. The failure stress for all the pins is Tfail=120 MPa and the failure stress for the bars between B-D is o fail =300 MPa. Assume that the beam ABC does not fail. Find the value of P such that the factor of safety (F.S.) for this structure equals 3. 8 mm- Top view -200 mm- D B B -180 mm 20 mm Front view 12 mm C P + P 8 mm 12 mm B Side view -8 mm D
please help solve and explain and include FBD please
. A helical compression spring is to be made of oil-tempered wire of 4 mm diameter with a spring index of C=10. The spring is to operate inside a hole, so buckling is not a problem, and the ends can be left plain. The free length of the spring should be 80 mm. A force of 50 N should deflect the spring 15 mm. (Take: G= 77 GPa) 1- Determine the minimum hole diameter for the spring to operate in. 2-Determine the solid length. 3-Determine a static factor of safety based on the yielding of the spring if it is compressed to its solid length.
I need neat Handwritten Solution. Answer: 1.07
Q2: The compression member shown in Figure below is pinned at both ends and supported in the weak direction. A service dead load of 150 kips and a service live load 250 kips must be supported. Use Fy = 50 ksi and select the lightest W-shape. 王江 14' 14 12' 12

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

ON 47 A link of S-shape made of a round steel bar is shown in Figure. It is made of plain carbon steel 45C8 (Syt = 380 N/mm2) and the factor of safety is 4.5. Calculate the dimensions of the %3D link. (d = 23.38 mm) %3D