oad factor. Q3// The monthly readings of a kW Energy consumed - 36,000 kWh consumer's meter are as follows: Maximum demand = 50 Reactive energy = 23,400 kVA R If the tariff is Rs 80 per kW of maximum demand plus 8 paise per unit plus 0-5 paise per uni for each 1% of power factor below 86%, calculate the monthly bill of the consumer. miccion line delivers 1190 kW at 33 kV at 0-8 p.f.

oad factor. Q3// The monthly readings of a kW Energy consumed - 36,000 kWh consumer's meter are as follows: Maximum demand = 50 Reactive energy = 23,400 kVA R If the tariff is Rs 80 per kW of maximum demand plus 8 paise per unit plus 0-5 paise per uni for each 1% of power factor below 86%, calculate the monthly bill of the consumer. miccion line delivers 1190 kW at 33 kV at 0-8 p.f.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Enlist the power quality issues for renewable energy integration
write the solution in hand-written please. thanks
Three-phase electricity is delivered to a factory 7 km from a distribution company. The factory receives a total of 2000 kW of power at a voltage of 10.98 kV (rms) per phase. If the transmission cable in each phase has a resistance of 1.8 per 10 km, then the total power lost in the cables of this three-phase system is (a) 4.645 W (b) 13.93 W (c) 4.645 kW (d) 13.93 kW
A load of 138+j460 Ohm is supplied through 3+j14 Ohm line as shown in Figure 1. (a) Find the average power dissipated in the line. (b) Find the value of capacitive reactance connected across the load to compensate the reactive power need of the load. (c) What is the equivalent impedance after compensation. (d) Find the average power dissipated in the line when the capacitive reactance is connected across the load. (e) Express the power loss in (d) as a percentage of the power found in (a) j14 Figure 1 7200/0 + V (rms) Source 3 wi Line Load 138 j460
A SUBSTATION RATED 1250 KVA IS OPERATING AT FULL LOAD AT 0.8 PF LAGGING AND TO CARRY AN ADDITIONAL LOAD OF 170 KW AT 0.85 PF LAGGING. WITH THE MENTIONED POWER FACTOR, THE SUBSTATION IS EXPERIENCING AN INEFFICIENT ELECTRICAL SYSTEM: HIGH POWER LOSSES, HIGH VOLTAGE DROPS IN THE ELECTRICAL EQUIPMENT, AND HIGH ELECTRICITY BILLS. TO REDUCE POWER LOSSES AND TO REDUCE THE ELECTRICITY BILL, POWER FACTOR CORRECTION IS TO BE OF HIGH IMPORTANCE AND CONSIDERATION. ANSWER: CITE A STEP BY STEP SUMMARY OF HOW TO DETERMINE THE POWER FACTOR CORRECTION REQUIRED IN THE GIVEN PROBLEM TO ARRIVE AT THE ALTERNATIVE THAT SHALL BE SYSTEMATICALLY CARRIED OUT TO GUARANTEE A SUCCESSFUL DECISION IMPLEMENTATION,
A generating station has a maximum demand of 30,000 kW. Calculate the cost per unit generated from the following data: Capital cost = P 130M; Annual load factor = 50%; Annual cost of fuel and oil = P7.5M ; Taxes, wages and salaries etc. = P7M and Interest and depreciation = 12%
For the system as shown in the following figure, convert the components to same base voltage and apparent power, by choosing 100 kVA as the base kVA and 2000 V as the base voltage for the generators. Redraw the single line diagram with the new per unit values. 15 KVA 2000 V Z=j0.3 pu 25 KVA 2000 V Z=j0.15 pu G1 G2 35 KVA 2000/8000 V Z=j0.2 pu Z=30+j100 Z=60+j120 pu O pu leee 35 KVA 8000/2000 V Z=j0.3 pu 35 kVA 2000/8000 V Z=j0.25 pu G3 10 KVA 2000V Z=j0.35 pu M 30 KVA 2000 V
A load of 23 kVA, with .65 power factor lagging is connected to a 240 volts line. How much capacitive reactive power is needed to correct the power factor to 0.95 lagging? Express in four decimal places.
A system consists of four idenital 400 MVA generating units feed- ing a total load of 1016 MW. The intertia constant of each unit is 5 on 400 MVA base. The load changes by 1.5% for a 1% change in frequency. When there is sudden drop in load by 16 MW, obtain the power system time constant (T) with constants H and D expressed on 1600 MVA base.