For a single phase ac voltage controller/chopper, which is designed by using thyristors, with the series R (=38[Ohm]) and L(=30 [mH]) load, if the rms value of the current flowing through each thyristor in the chopper circuit is equal to 0.83[A], then calculate average power absorbed by the load. 288.3204 W O 187.5384 W O 128.1424 W 64.8529 W O 38.5784W O 120.5604 W O 52.3564 W O 91.3782 W

For a single phase ac voltage controller/chopper, which is designed by using thyristors, with the series R (=38[Ohm]) and L(=30 [mH]) load, if the rms value of the current flowing through each thyristor in the chopper circuit is equal to 0.83[A], then calculate average power absorbed by the load. 288.3204 W O 187.5384 W O 128.1424 W 64.8529 W O 38.5784W O 120.5604 W O 52.3564 W O 91.3782 W

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

urgent required.
An ac controller has a resistive load of R = 10 2 and the input is 220 V, 50 Hz. The thyristors switch is on for n 25 cycles and for m 75 cycles. Determine: (i) (ii) (iii) the rms value of the output voltage, the input power factor, the average and rms current through thyristors.
Problem 2 The circuit diagram of a certain load is presented below. Determine the following: a. The power factor of the load. b. If the load is connected across a 400 Vrms source, determine the real and reactive power consumed by the load. c. From (b), determine the value of the capacitor to be placed in parallel with the load in order to improve the power factor of the load to 95% lagging. From (b), A synchronous motor is installed in parallel with the load to correct the pf. The motor is rated 5 hp operating at 60% efficiency. Assuming that the motor is running at rated power. Determine the apparent power and power factor of the motor in order to improve the load's pf to 95% lagging. 202 500 µF HI + VL -20 mH 5Ω >0.5VL m 15 mH
Eo(LL) (V) a) 3000 b) 2500 2000 1500 1000 500 0 No-load excitation curve @3600rpm 0 1 2 3 4 5 6 DC Excitation current (A) 7 The figure above shows the no-load excitation (LL) curve of a 3-ph, 2-pole, 60 Hz, 1000 kVA, 2.3 kV synchronous alternator at rated speed. The alternator has negligible resistance and Synchronous Reactance Xs = 1.2 n/phase. If the alternator is synchronized to the Power Grid at 2.3 kV (Line to Line), calculate the following: 8 9 10 The value of excitation current required for full load current at 0.7 pf lagging (over-excited). |EO(LL)I IF The alternator current and reactive power when it is delivering 80% rated power (0.8 MW) and its DC excitation current is 4 A. IL Q3ph
A synchronous generator has been synchronized to an infinite grid of 13.8 kV and 60 Hz. The generator prime mover C/C is such that the no-load frequency is 62.5 Hz and the power slope is 1 MW/Hz. The AVR C/C (The reactive power against the terminal voltage C/C) is such that the zero reactive power voltage is 14.6 kV, while the slope is 0.4 MVAR/kV. Calculate: (a) the kVA loading of the generator and its power factor. (b) the settings of the prime mover and AVR such that the generator delivers 3 MW at 0.85 lagging power factor.
??
In a given system of base power of 250 MW, and bus 3 is taken as reference. The per-unit reactances are X₁2 = 0.2 p.u., X13 = X23 = 0.1 p.u. If the power flow in the system is given as: PF12 = 100 MW, PF13 = 50 MW, PF23 = -150 MW, then the phase angles are Select one: O a. 0₁ = 0.02 rad., 0₂ = 0.06 rad., 03 = 0 rad. O b. None of these O c. 8₁ = 0.02 rad., 02 = -0.06 rad., 03= 0.1 rad. O d. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0.2 rad. O e. 8₁ = 0.02 rad., 8₂ = -0.06 rad., 03 = 0.1 rad. O f. 0₁ = 0.02 rad., 02 = -0.06 rad., 03 = 0 rad.
By comparing the principle of operation of a "three" phase generation system with a single-phase system, state what are the bendfits of three phase systems? In your own words, define the "skin effect" in transmission lines and discuss how can it be minimised? Name three advantages of AC transmission in comparison to DC transmission. What are the units of active, reactive and apparent power? The current in a single-phase motor lags 50° behind the voltage. What is the power factor of the motor?
Real Power Versus Voltage curve may be used to assess the a.Steady state voltage stability b.Loading of that particular AC Generator c.Dynamic voltage stability d.Complete Voltage stability 2- kinetic energy stored in the rotor of a synchronous alternator is given by a.G * H * w b.m * a c.0.5*m*v*v d.S * H
I need the answer quickly
Explain the concept of power quality and the various disturbances that can affect it, such as harmonics and transients.
Q1) A single-phase AC voltage controller is connected to an inductive load with a resistance of 10 and load impedance angle of 45°. The input ac voltage is 230 V at 50 Hz. (a) Draw the load voltage waveforms and derive an expression for the rms load voltage. (b) Determine the maximum load voltage, maximum load current, and range of delay angie for which the load voltage does not change.