Note: The indicated total potential difference in in the circuit as shown in the figure below is 45. V. R1 2. 3. 5 kO 45 V 10 k2 A2 75kQ 1 4. R3 6. Analyze the given figure below. Find V1, V2, V3, lo, I1, 12, and la. lo R=6-2 Vo = 60-V R2=10-2 R3 = 8- 12

Q: could you help me please it's one question

A: NOTE :- According to our company policy, experts can answer only 3 subparts at a time. So please…

Q: Connections Between Engineering, Technology, Science, and Society:Question 1 Which statement…

A: Regional grid is formed by connecting transmission system of a particular area through transmission…

Q: Sensors are used to monitor the pressure and the temperature of a c at. The circuitry for each…

A:

Q: Answer the following as completely as possible in your own words: 1. What is the stack? 2. How does…

A: 1)A stack is an example of a linear data structure. Linear data structures are collections of…

Q: Clear Explanation on this question add some step to leading to this how you get this answer neat…

A: a.. So according to the question ,we have to place the two rods parallel to x-axis.So our…

Q: This doesn't match the answer on the answer key I submitted with it - I was hoping to know the…

A: The required parameters can be calculated by using the equivalent impedance of capacitor and…

Q: Match V1(s) and V2(s) to the appropriate graphs of v(t) on the following page. 90 100 v1(s) V2(s)…

A: The single in time domain for 1st function is calculated by taking the Laplace inverse of the signal…

Q: QUESTION 4 What are the advantages of sourcing output cards? O Easier to interface to because one…

A: Concept- Sinking and Sourcing- PLCs use input/output module cards called Sinking and Sourcing.…

Q: 1. Work on the three Sub parts of the problem below using the explanation steps from the part of the…

A: Current Transformer 1) It is used to measure High current. 2) It is connected in series with the…

Q: current of 1 mA and a reverse bi Ans. Rp=9.3 k2; R.=6 kM

A:

Q: 1. If this were a real circuit, what would be the sources of experimental error? (Remember…

A: In any examination including flows there are numerous potential wellsprings of mistake, here are a…

Q: f(t) M fricfionless surfaće X = 0 f(t) M frictionless surfaće С. x = 0 f(t) M frictionless surfaće…

A:

Q: can you please help me with the code for matlab

A: d.The continuous time signals are given bya. x(t)=u(t+1)−2u(t−1)+u(t−3).b.…

Q: How do you solve equation 2 and 3? I can't come up with that answer?

A: here we are asked to solve equation 2 and 3 only.

Q: Determine the power dissipated by the 12 resistor. The power dissipated by the 12 resistor is W.

A:

Q: . A solar cell can be approximately modeled by the linear circuit in the Figure at right. a) Suppose…

A: Given:a solar cell approximate model,To do:a) If two identical solar cells are connected in series…

Dielectric Breakdown

A dielectric is a material with low electrical conductivity and so is classified as an insulator. Dielectric materials are used to block the flow of electricity through them, allowing them to behave as an insulators. They can also be used to store electric charge or improve capacitance.Dielectrics have no free electrons for conduction because electrons are tightly bound to the nucleus. Because dielectrics contain a small number of electrons for electrical conductivity, they have a dipole. The two primary roles of dielectrics in electrical devices are insulation and electrical energy storage. An electric field polarizes the dielectric, and the polarization of the molecules allows dielectric materials to store charge.