A)Determine the LRFD design strength and the ASD allowablestrength of sections shown in the figure.Use A36 steel and 4-in Ø bolts.-L6x 3늘 x를2 in3 in3 in 4 in 4 in

According to given data Determine the LRFD design strength and the ASD allowable strength of…

Answered: ngth of sections shown in the figure.…

Engineering

Civil Engineering

ngth of sections shown in the figure. A36 steel and 4-in Ø bolts. -L6x 3를 x 를 2} in 3 in -le le

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.2P

See similar textbooks

Similar questions

1.A tension member is 25 mm thick plate as shown. The bolts are 20 mm. diameter high-strength bolts. The steel is A36. Compute the following: 130 mm 25 mm 0 0 a) The design strength for LFRD. b) The allowable strength for ASD. 25 mm CIVIL ENGINEERING STEEL DESIGN
The tension member is a PL 1⁄2 × 6. It is connected to a 3⁄8-inch-thick gusset plate with 7⁄8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16’’ Use: Consider deformation at the bolt hole what is the: minimum spacing as per AISC code provisions maximum spacing as per AISC code provisions minimum edge distance as per AISC code provisions maximum edge distance as per AISC code provisions
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 2-inch-diameter bolts. Assume that A₂ = 0.75An. Ae 1 2 Determine the design tensile strength for LRFD. Determine the allowable strength for ASD. CIVIL ENGINEERING - STEEL DESIGN AL Section 2L5 x 3 x 516 LLBB
A C8 × 11.5 is connected to a gusset plale with 22 mm diameter bolts as shown. The steel is A572 Grade 50. If the member is subjected to dead load and live load only, what is the total scrvice load capacity if the live-to-dead load ratio is 3? Assume that Ae = 0.85Ap. a. Use LRFD. b. Use ASD. Properties of A572 Grade 50: Fy = 345 MPa C8 × 11.5 Fu = 448 MPa Properties of C8 x 11.5: Ag = 2,181 mm? br = 57.4 mm d= 203.2 mm Lw = 5.6 mm lf = 9.9 mm
The tension member is a PL 12 x 6. It is connected to a 38-inch-thick gusset plate with 7/8-inch-diameter bolts. Both components are of A242 steel. Note: A242 Fu = 70ksi dh = db + 1/16" Use: Consider deformation at the bolt hole 3" PL ... PL ½x 6 12" 24" 24" 12" a. What is the minimum spacing as per AISC code provisions Round your answer to 3 decimal places.
A double-angle shape, 2L7×4×3/s , is used as a tension member. The two angles are connected to a gusset plate with 7/8-inch- diameter bolts through the 7-inch legs, as shown in Figure P3.4-5. A572 Grade 50 steel is used. a. Compute the design strength. b. Compute the allowable strength. 2/2" 7" 3" 1/2" 2L7 × 4 × 3/s FIGURE P3.4-5
A C8 x 11.5 is connected to a gusset plate with 7/8 inch diameter bolts as shown in Figure P3.2-3. The steel is A572 Grade 50. If the member is subjected to a dead load and live load only, what is the total service load capacity if the live to dead load ratio is 3? Assume that Ae=0.85An. Use LRFD and ASD.
Design the size and length of Fillet weld for the lap joint shown below, Use SMAW E70XX process, plates are A-36 steel? 90k LL 40k DL R-X7 5" Gusset P 8 90k LL 40k DL
Tensile Strength A PL 3/8 x 7 tension member is connected with three 1-inch-diameter bolts, as shown in Figure P3.2-1. The steel is A36. Assume that Ae = An %3D and compute the following. a. The design strength for LRFD. b. The allowable strength for ASD. PL %x7 O o o
A double-angle shape is shown in the figure. The steel is A36, and the holes are for 1/2-inch-diameter bolts. Assume the Ae = 0.75An. Section 215 x 3 x %6 LLBB Determine the design tensile strength for LRFD. Select one: а. 66 b. 156 c. 78 d. 132
NEED ANSWER ASAP TY
The tension member shown in Figure 3.4-2 is a PL 5/8 x 10, and the steel is A36. The bolts are 7/8-inch in diameter. a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. | 2" +|+| in seinefrinehich 9 оо SO