n the clevis determine the minimum bolt diameter and the minimum thickness of each yoke that will support a load P = 55 KN without exceeding a shearing stress of 70 MPa and a bearing stress of 140 MPa. COMPLETE SOLUTION

Q: 1. A steel rod (initial diameter: 3.2 mm, initial length: 42 mm) is extended by a uniaxial tensile…

A: Given: Steel rod diameter, D= 3.2 mm Tensile load, F = 4800 N'

Q: A steel cube of side length L = 0.5 m is subjected to a shearing force of 5000N along the top…

A:

Q: Two strips of metal are pinned together as shown with a rod 10 mm diameter. The ultimate shear…

A: Given: Diameter=10mm Therefore, =5mm Shear stress=60Mpa.

Q: e plates in shear, what is the shear

A: We know, Shear stress=force/Area Given, Force=47kN Diameter=3.25mm Radius=1.625mm

Q: A circular metal column is to support load of 500 Tonne and it must not compress more than 0.1 mm.…

A:

Q: A circular rod of cross-sectional area 2 x 10m² has a tensile force of 80 kN applied to it. The…

A:

Q: A beam having the cross section shown is subjected to a vertical shear V. NOTE: This is a multi-part…

A: Consider the distance y from the bottom end where the shear stress is maximum.    As shown in the…

Q: A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters respectively equal…

A:

Q: Two solid cylindrical rods (1) and (2) are joined together at flange Band loaded, as shown. The…

A: ANSWER :- As in question normal stress is asked and can be calculated as force/area. Area of rod 1…

Q: A square lead slab of side 50 cm and thickness 10 cm is subjected to a shearing force (on its narrow…

A:

Q: Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P…

A: Consider the given data as below. Diameter of wire CD, dw=18 inch Diameter of the pin at B, dp=18…

Q: A metal slab of side (74+ 75) cm and thickness (74 + 25) cm is subjected to a tangential force of…

A:

Q: material is applied by a tensile forces of 132 kN on a bar of the material with a cross- sectional…

A: stress is defined as the force per unit area. Write the expression for stress. S=FA…

Q: Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the…

A: To find minimum diameter for each rod use the formula of normal stress and put the values to solve .…

Q: the maximum compressive load a bone

A: Given: Outside radius is ro=2 cm Inside radius is ri=1.5 cm Maximum stress is σ=153 MPa Note: 1…

Q: For the given state of stress, determine: (1) The principle stresses and the directions of the…

A: Solution:-           1). In the figure given we have:               σx= 350…

Q: The screwgate carabiner is left open as it is loaded by a rope as shown. Calculate the stress state…

A: Stress is defined as force per unit area.  σ=FA Where F is a force and A is cross-section area.

Q: Determine the outside diameter of a tube if the stress is limited to 128 MN/m2 and a hollow steel…

A:

Q: A wire of uniform cross sectional area of 0.25 mm2 is stretched at both ends by a total force of 65…

A: Given data The cross-sectional area is given as Ac = 0.25 mm2. The total force at both ends is…

Q: A structural steel bar with a 3.6 in. x 0.890 in. rectangular cross section is subjected to a…

A:

Q: A wrought iron wedge 2 cm long and 9 mm wide is used to attach a pulley to a shaft held still. The…

A: The given conditions for the problem are: A wrought iron wedge 2 cm long and 9 mm wide is used to…

Q: Circular notches are cut in a flat bar as shown. If w-25mm, t-12.5mm, r-3.5mm and the allowable…

A:

Q: he steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the shear stress…

A: Given: τallowable=70029645 Paϕall =2.24oϕall =2.24×π180ϕall =0.0390τallowable=70.029645×106…

Q: A 7-kip · ft torque is applied to a hollow aluminum shaft having the cross section shown. Neglecting…

A: Given data- T=7 kip-ft Radius of outer circle, r0=7 in Radius of inner circle, ri=14 in-4 in-2 in2=4…

Q: A load of 40 kg is suspended from a ceiling through a steel wire of radius 20 mm. Find the tensile…

A:

Q: A post having a hollow, circular cross sectionsupports a P = 3.2 kN load acting at the end of an…

A: Given P = 3.2 N b = 1.5 m L = 9 m S = 2.653105 mm3 r2 = 123 mm r1 = 117 mm τmax = 38 MPa σx = 90 MPa…

Q: A disk between vertebrae in the spine is subjected to a shearing force of 670 N. Find its shear…

A: The shear modulus is

Q: Tensile load of 2 MN is applied to an Aluminium cord with original diameter of 5 mm, the measured…

A: Given data: Magnitude of tensile load is, F=2 MN=2×106 N Original diameter of Aluminum cord is, d=5…

Q: The five-bolt connection must support an applied load of P-4700 lb. If the average shear stress in…

A: Given that - Five bolt connection Applied load(p)= 4700lb Averge shear stress in the bolt must be…

Q: A ceramic rod tensile test is applied to the cylinders and the strain value during tensile is…

A: Given that:Longitudinal strain, dL/L = 0.2%=2×10-3Lateral strain, dr/r =0.5× 0.04%=…

Q: The plot of tensile stress vs tensile strain of a certain rod has a slope of 25-GPa in the elastic…

A:

Q: A wooden timber is employed as a column under formwork. The timber is nominally 6x8 inches

A: Given: Axial stress is σ=600 psi(lb/in2) Area=5.5*7.5 in2 Area A=41.25 in2

Q: Assume if the shear stress in steel exceeds about 4.00 x108 N/m2 the steel ruptures. Determine the…

A:

Q: R [6r – (4)a a Find the maximum velocity for the velocity profile shown here (an expression based on…

A:

Q: Please no hand writing solution

A: Given that diameter of a solid circular shaft,D=2'' Applied torque,T=9 kip.in Strain ,ε=305×10-6

Q: Referring to Fig. compute the maximum force P that can be applied by the machine operator, If the…

A:

Q: A 3.5 cm cube of unknown metal has a shear modulus of 5.0x 10°N/m ? absorbed a force of 0.40 N.…

A:

Q: The five-bolt connection must support an applied load of P-4900 lb. If the average shear stress in…

A:

Q: A wire of uniform cross sectional area of 0.45 mm2 is stretched at both ends by a total force of 65…

A: