Moving to another question will save this response. Question 12 of 42> >> Question 12 Save Answer A short transmission line connects a step-up transformer on the source side with a series Impedance of 10.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary. The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) KV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +0.0816 ohms connected to its secondary side. A capacitor bank of j0.171 ohms is added parallel to the load Assuming an ideal transmission line, the load voltage (ine-to-neutral) would be: ⒸA 4900 V 8.12750V OC. None of the other choices are correct 0.7380 V OE62 KV

Moving to another question will save this response. Question 12 of 42> >> Question 12 Save Answer A short transmission line connects a step-up transformer on the source side with a series Impedance of 10.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary. The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) KV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +0.0816 ohms connected to its secondary side. A capacitor bank of j0.171 ohms is added parallel to the load Assuming an ideal transmission line, the load voltage (ine-to-neutral) would be: ⒸA 4900 V 8.12750V OC. None of the other choices are correct 0.7380 V OE62 KV

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A Cock-croft Walton type voltage multiplier has 7 stages with capacitance all equal 0.07pF. The supply a frequency of to be supplied is 6.5mA. to transformer secondary voltage is 133kV at 250HZ. If the load current The total voltage ripple of the system is: (a) 15.3kv (b) 12.2kv (c) 9.1kV (d) 10.4kv (e) 1.9kv a. d O b. a OC C O d. e O e. b
Ql-phase step down transformer 1250 KVA, 10002200 V, 50 Hz The resistance /phase and leakage reactanceiphase of the primary winding are 0.78 2 and 4.82 and the corresponding values for the secondary winding are 0.012 and 0.002 respectively if the primary winding is connected in delta and secondary in star calculate: )The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited li) The full load copper loss
Please answer all subparts than i will like a. A current transformer (CT) is rated 200/5 and has a secondary current of 4.0 A. Determine the primary current. b. A 150/5 CT has the primary conductor looped to pass through the donut three times. If the secondary current is 3.0 A, determine the primary current. c. A 60/5 CT has the primary looped to pass through the donut two times. With 25 A in the primary, determine the secondary current. d. A voltage (potential) transformer is rated for 14.4 kV / 115 V and is used to measure the voltage on an industrial power line. If the voltmeter indicates 111 V, calculate the voltage in the power line.
13)This MCQ QUESTION FROM BASIC POWER ELECTRICAL ENGINEERING course.
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RLs=0.0082 RHs=2.62 Rfe-HS=50002 XLs=0.015N XHs=5.2N Xm.Hs=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side. d) Input impedance if load is disconnected. e) Exciting current at no load.
In a single phase transformer, when no-load voltage is 230V and full load terminal voltage is 220, then the percentage regulation is 4.54%. Select one: True False
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RIs=0.0082 Rus=2.62 Rfc-HS=5000n XLs=0.0152 Xus=5.2 XmHs=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side. d) Input impedance if load is disconnected. e) Exciting current at no load.
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RLs-0.008Ω RHs-2.6Ω Ri-HS-500 0Ω XLS-0.015Ω XHs=5.22 Xm,HS=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side. d) Input impedance if load is disconnected. e) Exciting current at no load.
In part c determine the voltage across Rp and Xp .
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct