mass is connected to each other by rope. A 12 N F force is applied to body A at an angle of 10 °. There is only friction between body B and the inclined plane and the kinetic coefficient of friction is 0.3.   a) Draw the free body diagram of each object. b) Find the acceleration of the system.

Q: M2 = 5 kg uk = 0.1 M1 = 20 kg Two masses are connected as shown. There is no friction on the pulley…

A:

Q: A 3-meter-long 25 kg beam is supported by two cables as shown below. You can treat the beam as a…

A:

Q: B A 20cm Figure 1. Sketch of the problem. The 20 kg disc A is attached to the 10 kg block B using…

A: To Find : (a) If the disk rolls without slipping, determine its angular acceleration and the…

Q: A child goes down a playground slide with an acceleration a. coefficient of kinetic friction, Uk,…

A:

Q: Consider the following diagram. m1320 kg and m2= 10 kg. The system is being pulled by an applied…

A:

Q: An inventor wants to increase the efficiency of wood-burning stoves by reducing the energy lost…

A: Solution ;

Q: Don't Use Chat GPT Will Upvote And Give Handwritten Solution Please

A: I have solved the a) part by two methods1st method: We write the F=ma equation for all the masses…

Q: A luggage handler pulls a 20.0 kg suitcase up a amp inclined at 32.0° above the horizontal by a…

A:

Q: A car weighs 150 kilograms with a center mass at G. The horizon force P= 600 newton's. Please find…

A:

Q: AW-16-lb weight block is lifted vertically by a force of F-27 lb. Determine its acceleration. (Hint:…

A:

Q: A block with a mass of m = 1.8 kg rests on a wooden plank. The length of the wooden plank is 20 m…

A:

Q: A 3-meter-long 25 kg beam is supported by two cables as shown below. You can treat the beam as a…

A:

Q: An aircraft is getting loaded with checked luggage. The ramp that has a moving belt makes an angle…

A:

Q: A) what direction does friction act on at point A? B) a ladder weighs 20lbs on a rough floor (us=.8)…

A: To determine the force P, we will use the following equations- 1. Summation of all vertical forces…

Q: There is a system including two blocks. (ma = 2kg, mg = 8kg) This system starts movement from the…

A: Part (a) Write down the given value using suitable variables. Here mA signifies block A mass, mB…

Q: A winch, located at M, pulls a box up an incline with a cable. The distance from the box to the…

A: Given:To find:Speed of the box when it reaches the winch M.

Q: At the bottom of an incline at 45° to the horizontal, a 0.170 kg box is forced against a spring with…

A:

Q: N = F = i i mg mg

A:

Q: Q1. Consider the belt and pulley system in the figure below, Inertias other than that shown in the…

A:

Q: A) In terms of the mass of the block m, spring constant k, radius of the loop, R, and the…

A: Given Data:   To Find: (a) The minimum compression distance of the spring.

Q: 4. A body weighing 120 lb rests on an inclined plane, as shown. A force P parallel to and acting up…

A:

Q: P11. A cable is used to vertically lower an initially stationary fruits packet of mass 500 kg at a…

A: This question is on the topic of mechanics and spring compression. Here following unknowns need to…

Q: Consider the rod AB (mass m and length 10 m), that is simply resting between the ground and wall as…

A: Given: To find: Maximum mass

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.