The dredger is loading sand (SG = 2.6) onto a barge. The sand leaves the dredger pipe at 1.2 m/s with a weight flux of 3780 N/s. Estimate the tension on the mooring line caused by this loading process. Ans. 404.8 N

Q: Q1, ): A particular laminar boundary layer velocity profile is given by u(y) y 1+ A 2 Um Where y…

A: Given data: The velocity profile of a laminar boundary layer is given as : u(y)Um = 1 + Ayδ -…

Q: A turbine with a power coefficient Cp = 0.26 is able to generate 3.5 MW of electrical power with…

A:

Q: 9. The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a…

A:

Q: . The thin ( 3 mm ) thick plastic panel shown in the figure is lowered from a ship to a construction…

A: Thickness = 3 mm weight = 200 N velocity = 2 m/s

Q: The hoist supports the 145kg engine.  a) Determine magnitude of the force the load creates in…

A: The hoist supports the 145kg engine. a) Determine magnitude of the force the load creates in member…

Q: Q1) For the figure shown, D = 16 mm and V= 40 mm/s. When the force P is applied to the plate, the…

A: Given Data D=16 mm V=40 mm/s u=20y0.25 mm/s

Q: Two builders carry a sheet of drywall up a ramp. Assume that W = 1.9 m, L= 3.3 m, theta = 19.0°, and…

A:

Q: A B-2A is flying at 42,500 ft in standard day conditions at 420 KTAS. The mean chord length is 39.6…

A: Given Data

Q: (e) 1740 psf to Pa and kPa (f) 2.8 kips/ft? to kPa (g) 247 pcf to kN/m³ 3

A: a) convert psf to pa and kpa. b) convert kips/ft^3 to kpa c) convert pcf to KN/m^3

Q: Q3 For the given setup find the minimum force F, required to keep the walls in equilibrium. Assume…

A: Given:To find:Minimum force Fx required to keep the walls in equilibrium.

Q: Initial Final %3D Y = (3 m)sin 37° = 15 ms Xp = 0- %3D %3D m= 60 kg X - 3,0 m %3D Y= 0: V= 0. k=?…

A: Given data, Mass of cannonball, m=60 kg,Initial compresion in spring, xi=3 m,Final position:Initial…

Q: sailing vessels can carry lead ballast such as bricks to keep the vessel properly oriented and…

A:

Q: A69 A typical escalator in the London Under- ground rises at an angle of 30 to the horizontal. It…

A: Given: Vertical height (h)=15mTime taken by the escalator to reach h=1min or 60secNumber of people…

Q: Gate AB in the figure is 1.2 m long and 0.8 m into the paper. Compute the force F on the gate and…

A: Given:Length of gate =1.2 mwidth=0.8 mSG=0.82TO determine:The force F on gateand its center of…

Q: ce on the side of the "infinite" plate /m³. Assume g = 9.8m/s². 3

A: The fluid mass density is .The acceleration due to gravity is .

Q: A TRUCK is SHolelinG LiquiD slusH (8 = 20 kg/m³) THE SUSH is THROWN FORWARD AT e= 60° As SHOWN . THE…

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.