B A 20cm Figure 1. Sketch of the problem. The 20 kg disc A is attached to the 10 kg block B using the cable and pulley system shown in Fig. 1. The mass of the pulley can be neglected. (b) Calculate the tension in the cable. (a) If the disk rolls without slipping, determine its angular acceleration and the acceleration of the block when they are released. (50)

B A 20cm Figure 1. Sketch of the problem. The 20 kg disc A is attached to the 10 kg block B using the cable and pulley system shown in Fig. 1. The mass of the pulley can be neglected. (b) Calculate the tension in the cable. (a) If the disk rolls without slipping, determine its angular acceleration and the acceleration of the block when they are released. (50)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

4
Q5. A smooth uniform sphere of mass m and radius r is squeezed between the two massless levers, each of length I, which are inclined at an angle o with the vertical. If a force P is applied between the ends of the levers, as shown, what is the vertical acceleration of the sphere when p=30°? (Problem P3-1 in the text).
Wheels A and B are uniform 16.1-lb cylinders with frictionless axles as shown. A 32.2-lb box C with a center of mass at G is supported on the axles. Calculate the acceleration of the box if the wheels roll without slipping.
Problem 14.2 A 40 lb door with a width of 36 inches has a spring with an unstretched length of 4 in designed to close the door when left open. The spring is anchored as shown below when closed (solid outline is closed, dotted outline is open 90°). If we want the door to have an angular velocity of .2 rad/s upon closing when released from rest at 90°, what should the spring constant of the spring be? (This is the top view of the door below) 3 in (Solution: k = 2.68 lbs/ft=.224 lbs/in) Problem 14.3 4 in M 36 in
A garage door is mountedon an overhead rail (Fig.).The wheels at A and B have rustedso that they do not roll, but ratherslide along the track. The coefficientof kinetic friction is 0.52. The distancebetween the wheels is 2.00 m,and each is 0.50 m from the verticalsides of the door. The door is uniformand weighs 950 N. It is pushedto the left at constant speed by a horizontalforce F S , that is applied as shown in the figure. (a) If the distanceh is 1.60 m, what is the vertical component of the force exerted on eachwheel by the track? (b) Find the maximum value h can have withoutcausing one wheel to leave the track.
A round object of mass M and radius R roll down a hill of height h. Calculate the linear speed of the object (in terms of M, g, R, and h) when it reaches the bottom of the hill.
Dynamics Lesson:I want detailed and manual solution.
Problem #4) The extremities of a 4-ft rod weighing 50lb (1.5528slugs) can move freely and with no friction along two straight tracks. The rod is released with no velocity from the position shown, resulting in the rod to slide down the incline. The angular acceleration of the rod is a = +2.30k rad/s² and the linear acceleration at point A is 12.5674ft/s² to the right. Determine (a) ao, the linear acceleration at point G, and (b) RA and RB, the normal reaction forces at point A and B. Include and present the Free Body Diagram and Inertial Response Diagram as part of the solving process. B B=45° 4 ft G O D 30°1 A
Problem 1. Find the horizontal force magnitude P needed to start the motion of the block with mass mo in two scenarios: (a) when P is applied to the right and (b) when P is applied to the left. Develop a general solution for each scenario, and subsequently, substitute the values 0= 25°, m = mo = 2.5 kg, µs = 0.40, and μk = 0.35 into your expressions for evaluation. Hgs H k P (a) A mo 0 m P (b) B
A constant moment M in the clockwise direction is applied to a 20-lb thin disk in contact with an inclined surface. The kinetic friction coefficient is at the point of contact D. Determine the magnitude of the angular acceleration of the disk by neglecting the weight of the link AB, if M = 7.5 lb-ft and =0.4. Present your answer in rad/sec² using 3 significant figures. 1 in = 1/12 ft. 9 in. B M 30° D
dynamics
i need correct and stepwise answer i surely give you 3 likes