Marble ball having a density of 2700 kg/m³ and 1.5m diameter is supported with frictionless roller balls and used at a shopping mall for an entertainment purposes. A hydraulic system that has a 100mm diameter opening just below the ball lifts the sphere so its mass is felt like 20kg. necessary uplift pressure at the tip of the hydraulic system if the height of water in the tank is kept at 2m. Calculate the required pressure, P to create

Marble ball having a density of 2700 kg/m³ and 1.5m diameter is supported with frictionless roller balls and used at a shopping mall for an entertainment purposes. A hydraulic system that has a 100mm diameter opening just below the ball lifts the sphere so its mass is felt like 20kg. necessary uplift pressure at the tip of the hydraulic system if the height of water in the tank is kept at 2m. Calculate the required pressure, P to create

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

4. The siphon shown is 76 mm in diameter. It draws oil from a large tank. The loss of head up to the summit is 6 cm and from the summit to the exit is 23 cm of oil. a. Calculate the exit velocity. b. Calculate the pressure at the summit. 0.6 8.3 76- mm 0 siphon
The hydraulic press shown in Figure 9 is filled with oil with sp.gr. 0.82. Neglecting the weight of the two pistons, what force F on the handle is required to support the 10 kN weight? 75 mm Ø Hinge 10 kN oil 25 mm | mm| Figure 9 400 mm 25 mm Ø F
A cylindrical tank of water is 20 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground delivers water at a rate of 0.02 m/min. Ir the tank is initially half full, tal what is the water flow rate in m^3/sec from the top feeder pipe? (bi what is the pressure at the bottom of the tank? (Hint: Bernoul's principle) () what is the water speed at the bottom? (d) what is the leaking flow rate at the bottom? fe) at what rate is the volume of water changing? (Assume the tank is open to air at the top)
The hydraulic jack in the figure is filled with two types of oil, the specific gravity of oil 2 is equal to 80% of oil 1. Neglecting the weight of the two pistons, what force F (lb) on the handle is required to support the 2000-lbf weight for this design? Take the specific gravity of oil 1 = 0.9. 6 in 3 in 2000 lbf Oil 2 Oil 1 3-in diameter in 15 in 1-in diameter F
Problem 4: Inputs: ● ● B C Weight of person = 165 lb μ = 0.4 0 = 60° W A System 1 B C W a) Max weight that can be lifted in system 1 b) Max weight that can be lifted in system 2 System 2 Close-up view of pulley system In each scenario, you must determine the maximum weight, w, that can be lifted before the man slips. The problem starts out as a pulley problem, but thereafter it is a friction problem. (Thought you were done with that right?)
In a hydraulic press, the ram has a diameter of 20 cm and the plunger 2 cm. The fluid is an oil of specific gravity 0.8. Calculate the mass that can be raised by placing a mass of 100 kg on the plunger: (i)When the plunger and the ram are on the same horizontal plane, and (ii)When the liquid level in the plunger is 0.5 m above that in the ram. What is the mechanical advantage of the press in cases (i) and (ii) above?
Question Certain fluid parameters are provided The inner cylinder, with a diameter of 20 cm, remains stationary, while the outer cylinder, with a diameter of 21 cm, holds the liquid up to a height of 30 cm. There is a 1.0 cm gap between the bottom of the two cylinders. By rotating the outer cylinder at a speed of 200 revolutions per minute (r.p.m.), the torsion meter attached to the inner cylinder registers a torque of 6.0 N-m. a. Determine the toque on the bottom in terms of b. Determine the toque on the surface in terms of ..... c. Determine method the viscosity of a liquid (N-sec/m^2)(Ans up to 2 decimal) μ (Ans up to 4 decimal) ..u.(Ans up to 4 decimal) using the rotating cylinder
In a pump that works with cold water, the discharge pressure gauge located 7.5 m above the axis of the pump marks a pressure height of 68 m.c.a. The vacuum gauge located 125 cm below the axis of the pump shows a relative pressure of 325 Torr. Due to the difference in diameters between the suction pipes The momentum is created a dynamic height of ½ m. Calculate the useful head of the pump?