An closed cylindrical tank 4 m in diameter and 10 m high contains 4 m of oil sg = 0.9. An orifice 100 mm in diameter islocated at the bottom of the tank Cc = 1.00 and Cv = 0.97. Compute the time to discharge all the oil.

An closed cylindrical tank 4 m in diameter and 10 m high contains 4 m of oil sg = 0.9. An orifice 100 mm in diameter islocated at the bottom of the tank Cc = 1.00 and Cv = 0.97. Compute the time to discharge all the oil.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A water tank with a depth of h open to the atmosphere will be discharged through an outlet pipe with a diameter of 1 cm. The density of water is 1000 kg/m3, dynamic viscosity is 0.001 kg/ms. The pipe is 20 m long and there is a pump and a full open angle valve on the pipe. If the pump head supplied by the pump is hp = 2 m, the pressure at the outlet is 150 kPa and the outlet flow rate = 0.001 m3/h, calculate the height h. (Take atmospheric pressure as 100 kPa).
Oil (SG = 0.8, y = 0.010 Pa-s) flows through a 10-cm smooth pipe (length: 100 m) at a discharge of 0.010 m³/s, what is most approximately the head loss? O 7.21 m O 5.23 m O 1.28 m O 2.55 m
What pressure, p₁, is needed to produce a flowrate of 0.09 ft3/s from the tank shown in the figure below? Assume d = 0.071 ft. P1 = Mi ! psi Air P1 Gasoline diameter d→ Salt water SG = 1.1 2.0 ft 3.6 ft
Find the discharges in pipes 1, 2, and 3 in the reservoir system shown. The junction loss occurs for both flow from 1 to 3 or from 2 to 3. 50 m D; =0.3m L = 200m 20 m & =1mm D =0.5m 4=500m 4=1 mm p=999.1kg/m u=0.001139 kg / ms K=0.5 Kes =1 D=0.9m L =800 m Jnction Om 6=1mm
Given: diameter of orifice=100mm diameter of tank=1.2m C=0.65 solve for the time it takes to: a) remove the first liquid b) remove the second liquid c) completely drain the tank use 3 decimal places
Consider the tank shown in (Eigure 1). Take po = 900 kg/m³, Pu=1000 kg/m³, and pHg = 13 550 kg/m³. 0.6 m 0.8 m 100 mm h 1 of 1 > P Part A Determine the level of water in the tube if the depths of ol and water in the tank are 0.6 m and 0.8 m. respectively, and the height of mercury in the tube is h=0.075 m A Express your answer to three significant figures and include the appropriate units. PA h = 240 Submit + Provide Feedback → OF ? mm Previous Answers Request Answen X Incorrect; Try Again; 4 attempts remaining Next > 1231 AM 0
There are two liquid tanks A and B connected to each other by a tube as shown in the figure.The base of A is 75 cm2 and the base of B is 30 cm2. The density of the oil is 0.8. How many kilograms of oil must be put in tank B so that the level difference between the water in the two branches is 15 cm? Which point supports more pressure, C or C'?
6. Crude oil of relative density 0.91 (viscosity 1.24 poise) is pumped through a supply pipeline 75 mm diameter, where a flow of 420 litres/min takes place between pipeline section 1.25 km from the feeder reservoir, and section 1.60 km from the feeder reservoir. A piezometer records a pressure of 12425 Pa at the section D. Taking head loss due to friction into consideration as per viscous flow or turbulent flow prevailing, evaluate the pressure head at section 2.
A 12.5mm diameter orifice at the vertical side of the tank showed a discharge of 60 liters for every 85 seconds at a constant total producing head of 4.5m. Measurement of the jet showed that it travelled 2.4m horizontally while dropping 400mm. Determine the coefficient of discharge. A) No Answer among the choices В 0.612 C) 0.637 D 0.584 E 0.668
two vertical tanks, one with circular section 3.0m in diameter, the other square section 1.33 x 1.33m are connected by a short tube ( area is 0.725 sq. cm) near bottom.initially, the head of oil in the first tank is 4.0m, while in the second tank the head is 60m. After a quick opening of the tube valves, find the time for the oil surfaces to equalize. Assume the tube properties to be similar to that orifice, with c= 0.78
In a hydraulic press, the ram has a diameter of 20 cm and the plunger 2 cm. The fluid is an oil of specific gravity 0.8. Calculate the mass that can be raised by placing a mass of 100 kg on the plunger: (i)When the plunger and the ram are on the same horizontal plane, and (ii)When the liquid level in the plunger is 0.5 m above that in the ram. What is the mechanical advantage of the press in cases (i) and (ii) above?