6. Crude oil of relative density 0.91 (viscosity = 1.24 poise) is pumped through a supply pipeline 75 mm diameter, where a flow of 420 litres/min takes place between pipeline section 1.25 km from the feeder reservoir, and section 1.60 km from the feeder reservoir. A piezometer records a pressure of 12425 Pa at the section D. Taking head loss due to friction into consideration as per viscous flow or turbulent flow prevailing, evaluate the pressure head at section.

6. Crude oil of relative density 0.91 (viscosity = 1.24 poise) is pumped through a supply pipeline 75 mm diameter, where a flow of 420 litres/min takes place between pipeline section 1.25 km from the feeder reservoir, and section 1.60 km from the feeder reservoir. A piezometer records a pressure of 12425 Pa at the section D. Taking head loss due to friction into consideration as per viscous flow or turbulent flow prevailing, evaluate the pressure head at section.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Water injection is carried out in a 50 ft thick, 300 ft wide, and 400 ft long grid block (much like…

A: Given:- Water injection is carried out in a 50 ft thick, 300 ft wide, and 400 ft long grid block…

Q: . For the tank shown in figure below, determine the depth of the oil h if the reading of the bottom…

Q: Oil with density of (925 kg/m3 ) (9 = 0.00001 m2/s, and Q = 0.2 m3/s) is flowing through 500m pipe…

Q: The saturated liquid of water at T=300C has total volume (v) of 0.05m3,quality(x) of…

A: The formula used to calculate the specific volume; v=Vf+x(Vg-Vf) Where, V=Specific volumeVf=Specific…

Q: Glycerin (specific gravity 1.26) in a processing plant flows in a pipe at a rate of 805 L/s. At a…

A: Given data:

Q: Plot Xa and S/Sº vs Theta for So= 2000, 200, 20, and 2.

A: Given that :-Required that :-

Q: A = Roll 16 kN/m' 6 m 4 6m + M = 96 kNm 4 m B = Pin

Q: Determine the elevation at point A (ha) if the air pressure in the sealed left tank is -32 kPa. All…

Q: Problem 2 For the closed tank with Bourdon-tube gages tapped into it, what is the specific gravity…

Q: 8. The upper portion of an inverted U-tube is filled with oil having a pecific gravity of 0.98. The…

A: Determine the pressure difference (PB - PA).

Q: An oil of viscosity 0.01 Ns/m² is flowing between two stationary parallel plates 2 m wide maintained…

A: Certainly, here are the given data from your question:1. Viscosity () = 0.01 Ns/m2. Distance between…

Q: A rectangular block of 20 kg with bottom dimensions 100 x 200 mm slides down a 10° incline on a film…

Q: uid mechan

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A decision has to be made on wether touse 3 in or 4 in ID tubing for a well with the flowing…

A: Step 1: RequiredTo determine whether to use 3-inch or 4-inch internal diameter (ID) tubing for the…

Q: Design a rapid mix tank for water at 50° F flowing at Q = 4.0 MGD for a typical process train in a…

Q: Fresh and seawather flowing in parallel horizontal pipelines are connected to each other by a double…

A: The double U type manometer is provided in the above figure. We have to find out the pressure…

Q: Oil flows through a 200 mm diameter horizontal cast iron pipe (friction factor f = 0.0225) of length…

A: Given data- Diameter D=200 mm =0.2 m, Friction factor f=0.0225, Length L=500 m, Flow Q=0.32 m3/s,…

Q: A settling chamber is to be used to collect particles with a density of 1200 kg/m3 from an air…

A: A settling chamber is to be used to collect particles with a density of 1200 kg/m3 from an air…

Question

6. Crude oil of relative density 0.91 (viscosity 1.24 poise) is pumped through a supply pipeline 75
mm diameter, where a flow of 420 litres/min takes place between pipeline section 1.25 km from
the feeder reservoir, and section 1.60 km from the feeder reservoir. A piezometer records a
pressure of 12425 Pa at the section D. Taking head loss due to friction into consideration as per
viscous flow or turbulent flow prevailing, evaluate the pressure head at section 2.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data of the pipe flow

VIEW

Step 2: Determining the type of flow

VIEW

Step 3: Evaluation of pressure head at section 2

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 12 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Mass and mass related variables in engineering

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

natt10
A pressure gage at elevation 12 m at the side of the tank containing liquid reads 100 kPa. Another gage at elevation 7 m reads 140 kPa.Compute the specific weight of the liquid in kN/cu.m
A laboratory fermentor is equipped with a baffled disc-blade turbine mixer with a diameter of 0.1m and width 0.02m. The vessel is of a cylindrical geometry with inside diameter of 0.3m, filled to a height of 0.3m. The turbine speed of rotation for adequate mixing is 600 rpm. If the process is to be scaled-up to a fermentor with a capacity of 1.0 m3 , observing geometrical similarities and maintaining the same mixing rate establish the following; i. The speed of revolution for the larger vessel ii. Will a 2.5 kW motor be sufficiently strong to run the larger vessel? Use the power curve and the relationships provided overleaf, with the symbols having their usual meanings
Provide solution asap
For the permeameter shown below, develop a table showing the pressure head, elevation head and total head at the labeled points. Please present this table as your answer and show all work. 10m 7m 5m 3m 2m Soil
Glycerin at 20 °C flows upward in a vertical 75-mm-diameter pipe with a centerline velocity of 3.8 m/s. Determine the (a) head loss and (b) pressure drop in a 10-m length of the pipe.
Oil having sp. gr. of 0.9 and viscosity v 0.0002 m2/s flows upward through an inclined pipe as shown. Determine the flow rate. Ans. 7.64 L/s 6 cm diameter P2 250 kPa 40 Pi 350 kPa
Number 15. complete solution and box final answer
Please explain so I can understand
Pls answeer with complete solution written TY ASAP
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V3 (m/s) (b) The pressure at section B, ps (kPa) (c) FMx (N) de = 100 mm B da = 150 mm 30°
Oil with specific gravity of 0.88 flows through a pipe which changes from 6 in. at section A to 18 in. at section B. Section A is 12 ft lower than B and the pressures are 13.2 psi and 8.75 psi, respectively. If the flow rate is 5.17 cfs, determine (a) The velocity (ft/s) at section A, (b) The velocity (ft/s) at section B, (c) The head lost (ft) between the two points, and (d) The direction of flow. Is it from A to B or B to A?