7. An ejector mechanism consists of a helical compression spring having a spring constant of k = 98.1 kN/m. It is precom-pressed by 100 mm from its free state. If it is used to eject a mass of 100 kg held on it, the mass will move up through a distance of (a) 100 mm (c) 581 mm Mass Spring (b) 500 mm (d) 1000 mm

7. An ejector mechanism consists of a helical compression spring having a spring constant of k = 98.1 kN/m. It is precom-pressed by 100 mm from its free state. If it is used to eject a mass of 100 kg held on it, the mass will move up through a distance of (a) 100 mm (c) 581 mm Mass Spring (b) 500 mm (d) 1000 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The particle of mass m = 2.3 kg is attached to the end of the light rigid bar of length L = 0.83 m. The system is released from rest while in the horizontal position shown, at which the torsional spring is undeflected. The bar is then observed to rotate 45° before stopping momentarily, (a) Determine the value of the torsional spring constant kr. (b) For this value of kr, determine the speed vof the particle when e = 25°. kT Part 1 Position 1 is the horizontal orientation shown in the figure. Position 2 is the orientation when e- 45. Find the kinetic energy in positions 1 and 2. Answers: T1- kg m²/s2 T2- kg m²/s? Answers: (a) ky = i Nem/rad (b) m/s
M' M W L W = 7.5 mm 1,384 mm the steel plate in length turns into a full circle shape under the influence of moments acting on its ends. Steel (E = 113 GPa) SAFETY STRESS ON STEEL PLATES 479 MPa according to the maximum thickness of the plate (t) how many mm How many Nmm is the moment acting on the plate
A closed coil helical spring has 20 coils. If 4 coils of the spring are removed by cutting, the stiffness of the modified spring will be: A Of initial stiffness 2.5 time B Of initial stiffness 1.5 time C Of initial stiffness 1.25 time D Of initial stiffness 0.80 time
For what value M of the clockwise couple will the horizontal component Ax of the pin reaction at A be zero? If a couple of that same magnitude M were applied in a counterclockwise direction, what would be the value of Ax? -2.3 2.3 P 220 lb Answers: M- Ax i 1.8' 64 lb-ft lb .8'
2. A linear spring of stiffness k N/mm is to be designed to stop a railroad car, with a mass of m kg, traveling at v, km/hr within x mm after impact. Find the smallest value of k, in terms of m, ve, and x, that will produce the desired result. Hint: a dx = v dv. mim Vo k wwwM
The150-lb weight is attached to a rope that passes over the fixed cylinders A and B. The coefficient of static friction between the rope and the cylinders is 0.3. Determine the smallest force P that keeps the system at rest.
The unstretched length of spring AB is 3 m. If the block is held in the equilibrium position shown, determine the mass of the block at D. Give your answer in kg and to 3 significant figures. 3 m- 3 m www. KAC = 20 N/m -4 m- www wwwww B KAB = 30 N/m
18. If a close coiled helical spring absorbs 30 Nmm [S-toof energy while extending by 5mm, its stiffness will be (b) 4 N/mm (a) 2 N/mm sqa-bun ann and (c) 6 N/mm (d) red boxit 10 N/mm q
2. The frame is used to support the 50-kg cylinder. Determine the horizontal and vertical components of reaction at A and D. 0.8 m -0.8 m 100 mm C 100 mm 12 m
For the structure below, draw a free body diagram of the loaded system and then determine the reactions at A and B. 40 lb 10 in. 30° 50 lb 0 in. 20
A drum with a 500-mm radius is attached to a disk with a radius of 250 mm. The disk and drum have a combined mass of 15 kg and a combined radius of gyration of 400 mm. A 12 kg block D is suspended by a wire that is warped around the drum. Another force P- 100 Nis applied to the wire that is warped around the disk. If the system is released from rest, neglecting the effect of axle friction determine: (a) the acceleration of the block. (b) the velocity of the block after 10 second. (c) the distance travelled by the block after 10 second. (d) the revolution by the drum just after 10 second. 500 mm P+ 250 mm
A long column such as the one depicted below loaded in compression initially along its axis has a tendency to rotate. Associated with that rotation the load P imparts tipping moments that are resisted by the springs. In the configuration below the springs are connected to the rod with a frictionless slider and remain perpendicular to the rod. The pivot at O is also frictionless, and the masses of the structure are negligible. P k L k (spring) Assume that the springs are at their happy (natural/unstretched) length when 0 = 0. (a) Let the spring constant k, the lengths b, L, and d be given parameters in the problem. Find the load load P as a function of the rotation angle 0 such that the system is in static equilibrium.