Consider the compound beam shown in (Figure 1).Assume C is a roller, B is a pin, and A is fixed. Supposethat w = 16.5 kN/m.Figure-3 mB6 m< 1 of 1Part ADetermine the component of the reaction at the support A.Express your answer to three significant figures and include the appropriate units.A₂ =SubmitPart BA₁ =ValueμARequest AnswerμÀValuePearsonDetermine the y component of the reaction at the support A.Express your answer to three significant figures and include the appropriate units.C→UnitsUnits??L1. Privacy Policy Permissions Contact Us |Review

Answered: Image /qna-images/answer/1bb6035c-2c90-4d7c-b051-c77b0ad5b131.jpg

Shsider the compound beam shown in (Figure 1). Assume C is a roller, B is a pin, and A is fixed. Suppose that w = 16.5 kN/m. Figure B 1 of 1 L. Determine the component of the reaction at the support A. Express your answer to three significant figures and include the appropriate units. A₂ = Submit Part B μA Value 3 Request Answer Units ? Determine the y component of the reaction at the support A. Express your answer to three significant figures and include the appropriate units. Review

Shsider the compound beam shown in (Figure 1). Assume C is a roller, B is a pin, and A is fixed. Suppose that w = 16.5 kN/m. Figure B 1 of 1 L. Determine the component of the reaction at the support A. Express your answer to three significant figures and include the appropriate units. A₂ = Submit Part B μA Value 3 Request Answer Units ? Determine the y component of the reaction at the support A. Express your answer to three significant figures and include the appropriate units. Review

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the magnitude of intensity q that will produce a fully plastic condition in the beam shown below (refer to figure). The beam is made of steel with yield stress = 108 ksi and has rectangular cross section as shown. (Hint: a sliding support prevents rotation but allows vertical displacement . Express your answer in lbs/inch, up to 1 decimal place)
Consider the beam shown in (Figure 1). The support at B can be assumed to be a roller. Suppose that w = 7 k/ft Figure 12 ft 12 ft < 1 of 1 Part A Determine the z and y components of reaction at A. Express your answers using three significant figures separated by a comma. [5] ΑΣΦ [. Az. Ay= Submit ▼ Part B Request Answer B₁ = Determine the y component of reaction at B. Express your answer using three significant figures. ΕΠΙ ΑΣΦ vec Pearson J1 vec 3 → ? ? k Revie
A compound shaft consisting of a bronze segment and an aluminum segment is acted upon by two torques as shown in figure 2. Solve to determine the uniform shaft diameter subject to the following conditions: tbr < 80 MPa, Tal < 55 MPa and the angle of rotation of the free end is limited to 6°. For Bronze, G = 35 GPa and for aluminum, G = 28 GPa.
6 - A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. Im B OPT. →→→→T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
Given the following data: Draw the FBD( and determine the reactions at support A (Show in your solution, 1 F1 = 338 F2 = 541 F3 = 197 What is the moment reaction (lb-ft) at the support? ( Type your answer in positive value, two (2) decimal places without the unit. F1 F2 B 0.5 ft - 8 ft +6 ft 5 ft- 30° F3
A closed coil helical spring has 20 coils. If 4 coils of the spring are removed by cutting, the stiffness of the modified spring will be: A Of initial stiffness 2.5 time B Of initial stiffness 1.5 time C Of initial stiffness 1.25 time D Of initial stiffness 0.80 time
1) The head H is connected to the cylinder of a compressor using six steel bolts. If the clamping force in each bolt is 4000N, determine the normal strain in the bolts. Each bolt has a diameter of 5 mm. If o₂ = 280 MPa and Est = 210GPa, what is the strain in each bolt when the nut is unscrewed so that the clamping force is released? a) 0.970 b) 0.203 c) 0.970(10-³) d) Insufficient information to determine because the stress is beyond yield point H &
Bar ABC is rigid and rotates freely about B. The loads consist of a point load and a uniform temperature change in both bars CD and EF. Determine the temperature change (AT) at which points A and E first come into contact. Report your answer rounded to the nearest degree. 100 in initial gap = 0.11 in F T E A = 2.0 in² AEF EEF = 12,000 ksi aEF LEF 100 in = 13.5 x 10-6 1/°F = 50 in B 14 k 100 in D с ACD= 1.5 in² ECD CD= 6.5 x 10-6 1/°F = 29,000 ksi = 150 in LCD Y Z
For the given system below, find the reactions exerted by the pin and the roller on the beam. Label these reactions as RA and RB respectively. (Include a clearly drawn fbd and indicate the concept used as basis in every working equation presented.)
TNT a 8 95% D7:20 Q44 D137 PROBLEM SET NO. 1_STRESS ANALYSIS_SIMPLE STRESS.pdf 1. As shown below, two pneumatic cylinders are used to control the motion and displacement of the device arm ABC. Assuming that the control rods attached at A and D each have a 20-mm diameter and happen to be parallel in the positicn shown. Solve for the average normal stress in (a) member AE, [b) member DG if the applied load at point Cis 800 N. 150 mm G00 m
The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for the aluminum, 83 GPa for steel and 35 GPa for bronze. Aluminum 100 mm -3 m- 4 kN.m Steel 75 mm -2 m 1.5 kN - m Bronze |--15m-l