MA le Pb Input to a 11-kV, 36, Y-connected, synch motor is 60 A. Effective resistance per phase Synchronous reactance per phase 12 3052 Find a) power supplied to the motor ( Pin) b) induced emf for a 0.8 leading a) Pin = √3 V. I. cost = √3 Pin = (3 /(11000) 914.52 kW 11000) (60) (0.8) = Pb b) Ep = √p - Ja (Zip) 1100020 -(60236.87") (1+0) induced emf per phase E 7528.95 L-11.31 VI E = 6 × √3 E = 13,040 V final ans. line E dapat A. 2,200 V 30 star-connected S.M. has a resistance of 0.6 2 and synch reactance of 6. Find generated emf and the angular retardation of the motor when input is 200kW Ed ولا 2200 √3 at unity pf. Ia Zsp - (62.49 20°)(0.6 +16) 40° E = 1,278.09 L-14.27° FO√3 E2213.71 V Angular retardation 14.27° bw Vand E tinanggal sign na (-) to dae man hingpot kung leading / lagging 2024-04-26 Problem A 3-phase, 220-V, 50-Hz, 1500 r.p.m., mesh- connected synchronous motor has a synchronous impedance of 4 ohm per phase. It receives an input line current of 30 A at a leading power factor of 0.8. Find the line value of the induced e.m.f. and the load angle expressed in mechanical degrees. Ans. 268V, 6°

MA le Pb Input to a 11-kV, 36, Y-connected, synch motor is 60 A. Effective resistance per phase Synchronous reactance per phase 12 3052 Find a) power supplied to the motor ( Pin) b) induced emf for a 0.8 leading a) Pin = √3 V. I. cost = √3 Pin = (3 /(11000) 914.52 kW 11000) (60) (0.8) = Pb b) Ep = √p - Ja (Zip) 1100020 -(60236.87") (1+0) induced emf per phase E 7528.95 L-11.31 VI E = 6 × √3 E = 13,040 V final ans. line E dapat A. 2,200 V 30 star-connected S.M. has a resistance of 0.6 2 and synch reactance of 6. Find generated emf and the angular retardation of the motor when input is 200kW Ed ولا 2200 √3 at unity pf. Ia Zsp - (62.49 20°)(0.6 +16) 40° E = 1,278.09 L-14.27° FO√3 E2213.71 V Angular retardation 14.27° bw Vand E tinanggal sign na (-) to dae man hingpot kung leading / lagging 2024-04-26 Problem A 3-phase, 220-V, 50-Hz, 1500 r.p.m., mesh- connected synchronous motor has a synchronous impedance of 4 ohm per phase. It receives an input line current of 30 A at a leading power factor of 0.8. Find the line value of the induced e.m.f. and the load angle expressed in mechanical degrees. Ans. 268V, 6°

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 1200 kW,60 Hz synchronous alternator A identical governor droop of 0.0005 Hz/kW.Machine A takes two third of 1000kW bus load at 60 Hz.lf an additional 800 kW load is connected to the bus determine (a) bus frequency (b) load on each machine. is in parallel with a 400 kW,60 Hz alternator B.Both machines have (a) 58.6 Hz (b) 566.67 kW, 433.33 kW. (a) 59.6 Hz (b) 866.67 kW, 133.33 kW (a) 59.8 Hz (b) 666.67 kW, 333.33 kW (a) 58.9 Hz (b) 766.67 kW, 233.33 kW
SYNCHRONOUS GENERATOR A 13.8 kV, 50-MVA, 0.9 p.f., 60 Hz, four pole, Y-connected synchronous generator has a synchronous reactance of 2.5 ohms, and an armature resistance of 0.2 ohm. At 60 Hz, its friction and windage losses are 1 MW, and its core losses are 1.5 MW. The field circuit has a dc voltage of 120 V, and the maximum field current is 5A. The current of the field circuit is adjustable over the range from 0 to 10 A. The OCC of this generator is shown in the figure.
current and on-time? 2. A 60V chopper drives a resistive load of 12fL The chopper frequency is set to 1 kHz. Calculate the values of average and rms load currents and load power for a turn-on time of (a) 0.2ms, (b) 0.6ms.
Q3) A 3-phase, 120kv, 1.5 MVA, alternator, its star connected armature winding has 10 effective resistance and 1002 synchronous reactance per phase find VR% at full load at: a) unity power factor, b) 0.8 lagging, c) 0.8 leading. (Ans. 1.56%, 7.36%, -5%)
A 100 MW, 13,800 volts 80% power factor synchronous generator has an ohmic resistance of 0.1 ohm and synchronous reactance of 0.42 ohm is operating at rated condition. Find the angle between the voltages.
T-a. The direction of rotation of a single-phase split-phase motor can be change by........ a) reversing the connection of the start winding b) reversing the connection of the run winding c) reversing the connection of the start and run winding at the same time d) "a" or "b", not "c" T-b. Single-phase split-phase motors using an electrolytic capacitor in the start winding circuit should not be cycled more than about__________ time per hour. a) 8 b) 12 c) 24 d) none of the above T-c. When replacing the capacitor in a capacitor-start induction-run motor, one must be sure to replace the bad capacitor with__________ . a) a smaller one b) one of the same size c) a larger one d) none of the above
Two shunt generators A and B operates in parallel and their load characteristicsmay be taken us straight lines. The voltage of the generator A falls from 240 V atno-load to 220 V at 200 A while that of B falls from 245 V at no load to 220 V at150 A. Determine the current which each machine supplies to a common load of300 A and the bus-bar voltage at this load.
can you calculate the efficiency of the alternator
7) A 2-pole three-phase 50Hz 36 stator slots synchronous generator where the coil spans for 0.8889 of the pole pitch. The coil pitch and the winding distribution factors will be, respectively: a) 0.9848, 0.9962. b) 0.9242, 0.9212. 0.9848, 0.9561. d) 0.9242, 0.9962. e) 0.9561,0.9848. f) none of the above.
A three-phase, 3.3 kV, 50 Hz power supply is used to drive an induction motor. The motor has an eight-pole, star-connected stator. The rotor is also star-connected, with the line ends brought out to sliprings for starting and speed control. At standstill, the open circuit voltage induced on the rotor, as measured between the sliprings, is 1475 V. At the full load speed, the frequency of the induced emf on the rotor winding is 2.5 Hz. The motor has the following parameters: Rc = 250 Q R₁ = 0.1Q Xm=250 X₁ = 0.35 Q R2 = 0.04X2 = 0.30 By referring the rotor quantities to the stator, calculate the following: (i) The shaft output power and torque of the fully loaded motor, if the corresponding friction and windage losses are 44 kW;
Please answer the question by showing step by step and explaining each step with details, please? Especially, by explaining why you used that formula or calculations. Thanks in advance. This question is related with electromechanical energy conversion (electrical electronic engineering).
A 50 kVA, 550 volt single phase alternator draws a field current 10A at rated load with the same field current. The open circuit emf and short circuit current are 300 V and 150 A. the ohmic resistance of the armature between terminals is 0.18 ohm. The ratio of effective to ohmic resistance maybe taken as 1.5 . Determine the regulation at 0.8 power factor lagging.