Lets consider a solid circular shaft having a diameter D = 40 mm subjected to a triangular distributed torque and fixed at C, as shown in the figure below. If it is made of a material having a shear modulus G = 30 GPa, determine the angle of twist at its end A. t =100 N.m/m 1 m C 0.5 m

Lets consider a solid circular shaft having a diameter D = 40 mm subjected to a triangular distributed torque and fixed at C, as shown in the figure below. If it is made of a material having a shear modulus G = 30 GPa, determine the angle of twist at its end A. t =100 N.m/m 1 m C 0.5 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 216 mm and a…

Q: Q.I: A shaft composed of segments AB, BC is fixed between the two walls at A and C and loaded as…

Q: A hollow bronze shaft (G=5000ksi) has an outer diameter of 3in and a wall thickness of 0.25in. The…

A: Given data: Converting all data into SI units. Modulus of rigidity G=5000 ksi=34473.8 Mpa Outer…

Q: (A,) See the figure below. There are two torques applied at B and D. Segment CD is a tube, while AB…

A: In the given problem, the dimensions and Modulus of rigidity have been converted to feet. Radius,…

Q: (a) Determine the support reactions for the stepped circular shaft shown below. (b) Plot the…

A: GIVEN :- T1=200lb-inT2=100lb-inT3=500lb-indAB=3 indCE=2 inE=30×106psiμ=0.3SOLUTION :-Torque on…

Q: A solid shaft 2 inch in diameter is subjected into two torques .If the total angle of twist is eight…

A: Givend=2inT1=200 lb ft=200×12=2400 lb in

Q: A two-segment shaft is used to transmit power at constant speed through the pulleys shown in the…

Q: A 1.30-in.-diameter solid shaft is subjected to an axial force of P = 2000 lb, a horizontal shear…

A: Solution:

Q: Two solid 1.625-in.-diameter steel shafts are connected by the gears shown in the figure. The shaft…

Q: A vertical shaft DA is attached vertically to a fixed base at A and is subjected to the torques as…

Q: Given the figure shown below, bronze and aluminum compound shaft are attached to rigid supports. The…

A: To find: The maximum torque carried by the aluminum shaft. Given: The diameter of bronze shaft is…

Q: Two solid 1.625-in.-diameter steel shafts are connected by the gears shown in the figure. The shaft…

A: To find:Maximum shear stress in each shaft

Q: A solid shaft in a rolling mill transmits 30 hp at 100 rpm. Find the diameter in mm of the shaft so…

Q: A stepped shaft ABCO consisting of solid circular segments is sublected to three torques, as shown…

Q: For the gear system shown in the figure, the diameter of shaft AB=12 mm. Determine the diameter of…

Q: The tubular rotor shaft of a wind turbine shown in Figure 3(a) is of 50 mm and 40 mm outer and inner…

A: Find the second moment of area about diametric axis.

Q: Determine the angle of rotation at the free end.

A: Given: To determine: The angle of rotation at the free end due to the torque applied

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Let's consider a solid circular shaft having a diameter D = 40 mm subjected to a triangular distributed torque and fixed at C, as shown in the
figure below. If it is made of a material having a shear modulus G = 30 GPa, determine the angle of twist at its end A.
t=100 N.m/m
1 m
0.5 m
Select one:
O -0.00226 rad
O -0.00553 rad
O -0.00875 rad
O -0.00167 rad
O-0.00407 rad

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 200 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 150 mm and a wall thickness of 10 mm. The shaft is subjected to torques TB = 42 kN-m and TC = 18 kN-m, which act in the directions shown in Figure. Determine the maximum shear stress magnitude in Segment (2). J1= 54019686 mm4J23D 21551281 mm4 TB Tc (2) O 88.8 MPa 62.3 MPa O 44.4 MPa 124 6 MPa
Figure Q1 shows a solid steel shaft AF which is supported by frictionless bearings at B and F. It is coupled to an electric motor at A. The modulus of rigidity of steel shaft is 75 GPa. The shaft is loaded by the torque as stated in the figure below. Answer the following:(a) Calculate the maximum shear stress in the shaft. (b) Determine the total angle of twist between F and A. (c) If speed of the shaft is 50 rev/s, calculate the required power transmitted by the electric motor to the shaft.
EXAMPLE: 10. A solid aluminum shaft 2 in. in diameter is subjected to two torques as shown in the figure. Determine the maximum shearing stress in each segment and the angle of rotation of the free end. Use G = 4 * 106 psi. (Practice at Home) 200 lb-ft f -2 ft → 3 ft- 800 lb-ft
ON 01 Figure Q1 shows a shaft AB (modulus of rigidity G = 73 GPa) with a total length of 1270 mm that is fixed at both ends. Section AC is solid with a diameter of do = 80 mm, while CB is a hollow section with an internal diameter of di = 60 mm. An external torque T, = 10 kN.m is applied at point D. (a) Determine the magnitude of the reaction torques at both supports if the distance x = 735 mm. (b) What is the maximum angle of twist, aand where does it occur? -635 mm- -635 mm- |A To В •D d,
1. A solid steel shaft ABCDE having diameter d = 40 mm turns with a constant angular velocity and freely in bearings at points A and E. The shaft is driven by a gear at C, which applies a torque T₂ = 625 N_m in the direction shown in the figure. Gears at B and D are driven by the shaft and have resisting torques T₁ and T3, acting in the opposite direction to the torque T2. We know T₁ = 400 N.m, but T3 is not explicitly given in the problem. Segments BC and CD have lengths LBC= 550 mm and LCD = 400 mm, respectively, and the shear modulus G = 80 GPa. Determine the maximum shear stress in each segment of the shaft and the angle of twist between gears B and D. pôrôć -LBC LCD T3 E
A steel stepped shaft ABCD fixed at A is subjected to three torques at points B, C and D, with magnitudes T₁ = 40 kip-in, T₂ = 50 kip-in and Ts= 30 kip-in and directions as shown in Figure 1.1. The segments AB and BC are solid with diameters dx = 3 in and dec = 2 in respectively, while segment CD is hollow with an outer diameter dan 1.5 in and a wall thickness of 0.25 in. The shear modulus of elasticity is equal to G=11.6x10³ ksl. T₁ T₂ 4 = 20 in A B L₂ = 20 in Figure 1.1 a) Draw the torsion moment diagram for the shaft and calculate how long should segment CD be so that the angle of twist between points B and D is equal to zero. T₁ 4₂-25 in b) If Ts is dropped, a fixed support is added at point D (as shown in Figure 1.2) and the length of segment CD is equal to 15 in, find the support reactions at points A and D and the maximum shear stress developed in segment BC. The magnitudes of the torques at points B and Care the same as in part a). B C L₂= 25 in T₂ * Figure 1.2 Hollow C Hollow…
A motor supplies a torque of 5.5KNm to the constant diameter steel (G= 80GPa) line shaft shown in the figure. Three machines are driven by the gears B, C, and D on the shaft, and they required torques of 3.0KNm, 1.5KNm, and 1.0KNm, respectively. Determine: a. The minimum diameter required if the maximum shearing stress in the shaft is limited to 100MPa.b. The rotation of gear D with respect to the coupling at A if the coupling and gears are spaced at 2m intervals and the shaft diameter is 75mm.
A shaft made from acrylic is subjected to the three torques indicated below. The acrylic has a shear modulus of 1.7 GPa. Determine: a. The twist at the end D if the diameter if the shaft is 100 mm. b. The minimum shaft diameter if Tallow = 10 MPa 200 N•m A 800 N•m 300 mm B 400 N•m 600 mm C 600 mm
Solve the following differential equation: dy – 2y – x*e-2x = 0 dx
Problem 3
3) Two circular shafts (shown in Figure) made of the same material and have the same length are subjected to a torque Tequals 150 lb.ft, the angle of twist for the hollow shaft equals that of the solid shaft. A-1/3 C-5.4 B-1 D-3 D=10 in solid shaft D=10 in d=9 in O hollow shaft
The solid shaft is fixed to the support at Cand subjected to the torsional loadings TA = 12 kN.m and TB = 3 kN.m in the directions shown by the figure. What is the angle of twist of end A with respect to end C? Take d = 120 mm, LAB = 263 mm, L BC = 184 mm and G = 75 GPa. %3D Tg LBc TA LAB