Let's consider a rod subjected to the shown axial forces. If we consider a lincar elastic behavior, determine the axlal force Fo so that the vertical displacement of end D is & = 0.6559 mm and Fc = 20 kN. Segments (1) and (2) are made of steel with a modulus of elasticity E = 200 GPa, while segment (3) is made of aluminum with a modulus of elasticity E = 70 GPa. The rod has a solid circular cross-section with the following diameters: D(1) = D[2) = 50 mm, D(3)

Let's consider a rod subjected to the shown axial forces. If we consider a lincar elastic behavior, determine the axlal force Fo so that the vertical displacement of end D is & = 0.6559 mm and Fc = 20 kN. Segments (1) and (2) are made of steel with a modulus of elasticity E = 200 GPa, while segment (3) is made of aluminum with a modulus of elasticity E = 70 GPa. The rod has a solid circular cross-section with the following diameters: D(1) = D[2) = 50 mm, D(3)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The bar shown below is composed of two pieces, AC and CD. The bar is attached to the wall at point A. The length L = 10 in. The cross sectional areas are: AAC = 4 in? and AcD = 2 in?. The Young's Moduli are: EAC =20 Msi and Ecd= 15 Msi Two forces are applied at points B and D: PB = 50 kips and PD = 20 kips. Determine: (a) the reaction force at A (specify –→ or +) and (b) the deflection of point D (specify → or +). (Hint for (b): Think about how many pieces you must subdivide the rod into.) Ans: RA = 30 kips (+), dp = 7.9167×10-3 in (E) A В C D Pp L 2L L
The assembly consists of two-rod brass C83400 copper alloy rods AB and CD of diameter 30 mm, a stainless 304 steel alloy rods EF and FG of diameter 40 mm, and a rigid cap H as shown in Figure 2. Neglect the size of the collar at F. Assume that the modulus of elasticity Esteel = 200 GPa and Ebrass = 101 GPa. If the force, P = 5 kN, (a) If the horizontal displacement of end G of rod FG is 0.6 mm, determine the new magnitude of P.
Please show complete solution and box the final answer
The figure below shows a section of a column subjected to load P, which is applied 50 mm from the midline of the section's web. The column is made from material, which has an allowable normal stress of 180 MPa (both in tension and compression). The area of the section is 10050 mm?; the principal moments of inertia Imar = 146.554x106 mm and Imin 20.076x10° mm*. !! Determine the maximum allowable load P. 15 mm 150 mm 15 mm 150 mm 50 mm 15 mm 100 mm 100 mm 1194.6 kN 363.6 kN 1809.0 kN O 516.4 kN O 189.5 kN
A given conical bar is tapering uniformly from 4 cm diameter to 15 cm and has a length of 40 cm. An axial force of 80 KN is applied at each end if the bar, Find the elongation of the bar. Note: Take E=200 GPa
H.W 1 A6 m long hollow bar of circular section has 140 mm diameter for a length of 4 m, while it has 120 mm diameter for a length of 2 m. The bore diameter is 80 mm throughout as shown in Fig. B 140 80 300 kN + 300 kN 80 120 4 m 2 m Find the elongation of the bar, when it is subjected to an axial tensile force of 300 kN. Take modulus of elasticity for the bar material as 200 GPa.
A steel torsion bar AB with diameter d = 34 mm, and ductile material of tensile yield strength Sy = 276 MPa is attached to a rigid arm at A, supported by a bearing at C, and fixed at B, as the picture shows. At the right end of the arm is mounted the wheel on which the vertical force P acts from the ground and which passes through the center of the wheel. If bearing C acts as a simple support and the effect of transverse shear due to P is negligible, determine the maximum force P (in kN) that can be applied to the wheel. Consider a factor of safety n = 2.5. Use the maximum energy of distortion failure criterion and do the analysis on bar AB (torsion bar) in the section where the bearing is.
A compression member constructed from steel rod (E = 200 GPa, v = 0.25) has outside diameter of 82 mm. What axial force P will cause the outside diameter to increase by 0.0087 mm? Assume that the material behaves linear elastically.
While the ABCD rigid beam shown in the figure is simply supported from the A point, it is supported by vertical BF and CE bars from the B and C points, respectively. There is no tension in the bars in the unloaded condition. Considering that the length of the BF rod is 800 mm in addition to the given dimensions, if a strain value of -600 um / m unit occurs in the BF rod when a vertical P load is applied from the D end, the elongation amount in the CE rod will be the following in mm.
Let's consider a rod having a solid circular cross-section with diameter of 4 mm and it is made of a material having a Young's modulus E = 120 Gpa and a Poisson's ratio of 0.33. When a tensile force F is subjected to that rod cross-section, the diameter becomes 3.995 mm. Determine the applied force F. Consider a linear elastic behavior.
I am struggling with this question