lem 4. The angle of intersection of a circular curve is 45°30' and its radius is 198.17m. PC is at Sta. 0+700. Compute ght angle offset from Sta. 0+736.58 on the curve to tangent through PC.

Q: d = 4" %3D x' b = 4" %3D B = 8" %3D H = 8" h = 4" d = 4"

A:

Q: 6. How can we write kinematic viscosity using the MLT system? a) [M][L][T]? b) [M]°[L]?[T]1 c)…

A:

Q: why set of standard weight used in calibration platform balance?

A: Calibration is the process of putting the scale through its paces to ensure it has the precision you…

Q: I need accurate ansswer with good content 454.  How do you measure distance in a high-rise building…

A: Laser scanning, also known as Terrestrial Laser Scanning (TLS) or 3D laser scanning, is a powerful…

Q: emperature when this system was assembled was 74F, what would be the stress in a temperature of 4OF?…

A: According to given data  The assembly below will be used for each problem Lengths, diameters, and…

Q: 6. Calculate the location of the centroid (x and y) of the area shown below. All dimension are in…

A: To determine the location of the centroid.

Q: For what reason must wires and plumbing fixtures installed above drop ceilings be plenum-rated?

A: Cables are distinguished as plenum and non-plenum based on the outer covering's (jacket) fire…

Q: QUESTION 5 Which of the following represents the location of the horizontal plastic neutral axis (X,…

A: Solution Find the location of horizontal plastic neutral axis

Q: Determine: a) Differential Area b)  Centroid distance along x and y axis   *use 3 decimal places…

A:

Q: QUESTION 1 rom the figure below, locate the cat id fx and y axes as shown. Y y2 y1 x1 x2 y1 y2 y3 x1…

A:

Q: If Block B travels when it is released from rest to the point that the speed becomes 3m/s. What is…

A: What is the distance created by block B

Q: net area in tension, Ant, of the L6 x 6x 3/8 angle shown in the figure is equal to:

A:

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: In the diagram shown, (aut cad) the correct steps for drawing a triangle starting from point B in…

A: @40<0,50<45,C INTER

Q: Determine the polar moment of inertia with respect to the centroidal X and Y axes. Present detailed…

A: Given: Required: Polar moment of inertia about centroidal x and y axes

Q: My book says the right answer was 90 kPa

A: Given data in question  Unit weight of dry bark clay 18 kN/m3 Saturated unit weight 15 kN/m3 and 21…

Q: Does the function, =Ur cos0+cose represent possible irrotational flow? r

A:

Q: Determine the x- and y-coordinates of the centroid of the shaded area shown. T 7" 16" Answers: x = y…

A:

Q: is required to find soil pressure at a depth of 10 ft beneath the interior corner A and exterior…

A:

Q: 1. Find the shortest path from A to D. B 2 3. 2 G 5 F8E

A:

Q: dy x³ex² dx ylny

A: Hello dear this is the solution of your problem Please see the attached solution, thanks

Q: 6. How can we write kinematic viscosity using the MLT system? a) [M][L][T]? b) [M]°[L]?[T]*1 c)…

A:

Q: What is the level rod reading in feet at the main crosshair line shown in the figure? (enter only a…

A:

Q: Q5: : In your own words, compare the following images, using a table.. dream dreamtime dreamsme dre…

A:

Q: 1) Find the coordinates of the centroid, xc and yc. 2) Calculate the second moment of inertia Ix' at…

A: Given data

Q: The section comprising of two 250 x 37 channels shown was built-up in such a way that their…

A:

Q: PROBLEM 2 The centroid of the T-section shown is 2.5 inches above the base. What should be the value…

A:

Q: Given: |Change in length of BE=0.00352a mm Area(BE)=150a mm? E Area(CF)=150a mm? E=200 GPa Required:…

A: To find the change in length of CF-

Q: Target Range (R) [m] σG A. P P, = (4 t)² R4 where: Pr = power received from the radar in units of…

A:

Q: sieve analysis what's the meaning or gonna happen if the So is zero

A: A sieve test is generally called as gradation test, is one of the most important and widely used…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. Y I Ti 0.34 al TE Answer: (x,…

A:

Q: H, = 19 mm, G, 2.51, Pa 1.73 g/cm d, = 0 division, Gauge factor = 0.01 (mm/division) Dial Gauge Dial…

A: Hi! Thank you for the question, As per the honor code, we are allowed to answer three sub-parts at a…

Q: A piece of ducting must be custom-made. It must fill a gap 257⁄16 inches long.One end of the duct…

A: Given:- a gap 257⁄16 inches long.One end of the duct must also fit into the next piece of ducting…

Q: Fill in the blanks Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that…

A: Determine the two possible angles so that the water strikes at B.?

Q: Determine EI8 at point B and end of the overhang. Round off your final answer in 2 decimal places.…

A:

Q: explain how to do this and what would be happened in autocad?

A: For the first figure, just use the line command and input the measurement values to draw the entire…

Q: Compute the Interior C. Compute the Interior B. Compute the Interior A. Compute the Interior D

A: Given Data- To Find- Internal Angles A,B,C & D

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.