Fill in the blanks Smaller angle: Larger angle: s = 20 ft Determine the two possible angles so that the water strikes at B. A = 40 ft/s 4 11 - 1 attachment 811

Q: A wood or metal strap installed at a 45 degree angle to plates to make a wall frame rigid is called

A: A wood/metal strap installed at 45° angel to plates to make a wall frame rigid is called......

Q: You have decided to build a deck on your new home 12 feet wide x 16 feet long, using the standard 2…

A:

Q: For 1.DU z The figure is made of a 4"radius half-circle inscribed in a 4" x 8"rectangle beside a 4"x…

A:

Q: Instructions: Solve the following problems. Show your complete solution and illustrations. Box your…

A: Normal stress is σn=12 ksi. Shearing stress is τ=14 ksi. Bearing stress is σb=18 ksi. Based on…

Q: Exercise 5: Identify the surfaces with the appropriate letter that would appear in the FRONT view,…

A:

Q: Calculate the shape factor of the cross-section shown. 200 12 250 600 50 50 700

A:

Q: The timber beam in Figure 2 is simply supported at points A and E. The cross-section of the beam…

A: E = 12 GPa Use virtual method to analyze the beam.

Q: You have a table as seen below. You'want to sit close to one edge, but when you sit, the other side…

A: Here,W = 4.4 mW1 = 1.2 mW2 = 1.6 mh = 1.1 mg = 9.81 m/s2Weight of table (N) = 32.7 kgWeight of…

Q: With respect to the given X & Y axis of the shaded section.

A:

Q: computer aided engineering

A: Computer-aided engineering (CAE) is the use of computer software to simulate performance in order to…

Q: Note: Replace all zero digits of your ID number by number "2" Problem #4: Use X = Last 3 digits of…

A:

Q: A frame ABCDE is subjected to forces Po, Pe, and a moment Mcas shown in the Figure below. If Po = 10…

A:

Q: Note: Replace all zero digits of your ID number by number "2" Problem #1: XN Use X Last 3 digits of…

A:

Q: Convert 1600 mils into equivalent value in grads O 90 degrees O 180 degrees O 270 degrees

A: To convert mils to degree

Q: Present a problem with solution solving the centroid of a miscellaneous solid.

A:

Q: Given the fence 20 meters long and 3 meters high, determine the total number of pieces of 10 mm…

A: ASSUME SPACING OF VERTICAL BARS= 0.4 METER

Q: A water supply system contains two parallel lines, each consisting of a pump along 400 ft of 8-inch…

A:

Q: What is the level rod reading in feet at the main crosshair line shown in the figure? (enter only a…

A:

Q: Please

A:

Q: Give the discharge/flow rate in (m3/s) of the system with a constant velocity of 2.5 m/s given the…

A: given - velocity,V and diameter,D to find - discharge, Q

Q: Break the shaded area into the five different areas shown. Find the area and thex- and y-coordinates…

A:

Q: For the objects shown on the left below with an indicated cutting plane. Circle the letter…

A: To select the correct option for the given figure with section shown on the left side.

Q: 1. Determine the Degree of Freedom of the following Structure 3k C. D 12n E D. 10 ft- 10 ft- 10ft 10…

A: Degree of freedom is the measure of the unknown movement that we have to address while solution that…

Q: Solve for the reactions and draw the shear and moment diagram. 9.35KN/m 2.00 5.00 116KN 9.35KN/m…

A:

Q: In fighting with fires, what is the correct way of using a fire extinguisher? A squeeze, aim, sweep,…

A: 1.E Pull, Aim, Squeeze, Sweep

Q: Given the fence 20 meters long and 3 meters high, determine the total length of 10mm horizontal…

A: Assume spacing =0.457 mtr

Q: For the cross-section shown below, the centroid value from the top surface in inches is: * 0.5 in.-3…

A:

Q: Question 1 What does the simple theory of elastic bending states? (at least 2 sentences).

A:

Q: PROBLEM 1: Determine Ix and Ix.

A: FInd…

Q: Solve for the reactions and draw the shear and moment diagram. 116KN

A: PLEASE POST OTHER QUESTIONS IN DIFFERENT QUESTION

Q: Figure 20-7 Questions 1-10. 44 8. 6 38 20 24 34 Ol 76 8 80 84 88 92 10 Match the dimensions…

A:

Q: Note: Replace all zero digits of your ID number by number "2" Problem #2: 2 m W = X N Use X = Last 3…

A:

Q: Determine the following: 1. Height of the object 2. Width of the object 3. Depth of the object…

A: 1. Height of the object = 2 + 1.25 = 3.25 ( Hint : Measured from Front View) 2. Width of the object…

Q: Please recheck and answer in 3 decimal places.

A:

Q: Two springs are used to support the steel truss structure of 2.5 m height shown in the figure. The…

A: Given: Spring 1: (right support) Shear modulus, G1=300+41=341 GPa Spring diameter, d1=20 mm Helical…

Q: Untitled -> O File | C:/Users/ecruz/Downloads/Basement%20Foundation%20Drawing(1).pdf Not syncing of…

A:

Q: Concrete strength of fck should be used. Reinforcement grade of fy should be used. Preliminary…

A: L=4.55 mh=22.2 mt=122 mmDL=3.55 kPaLL= 4.55 kPafck= 25.5 Mpafy= 472 MpaTo design1) Loads2) Design…

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.